FGID2466QF8A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from STILWELL, OK
- Parts Used:
- 5304507087
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Wouldn't fix it
The part wasn't correct and I have to pay postage back which is nearly as much as the part so it's stupid for me to spend more money on a part that want work I want order from your store again.
Was this instruction helpful to you?
Thank you for voting!
Plastic had melted on the screw
Eventually broke off old heating element to get it out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from hull, MA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom Spray Arm Did not Turn
The bottom spray arm would not turn or fall off the stem assembly, so the dishes would not come clean like usual. The spray arm connects to the stem assembly via two plastic prongs that secure the spray arm. I removed the spray arm from the socket (no tool required) and observed the prongs had worn completely away. I grabbed the power screw driver and removed the assembly (3 screws). I placed the new assembly in place, secured the screws, and attached the spray arm. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from ROANOKE, VA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part was damaged and dishes weren't clean
Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FT LAUDERDALE, FL
- Parts Used:
- 5304500204
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leak
watched a video, really easy fix. Solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from MARINE ST CRX, MN
- Parts Used:
- 5304532199
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaked spot free fluid
Replaced part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette from Fort Lauderdale, FL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from New Hope, PA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
Brass nuts holding heating element in place had split
All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul J from LEXINGTON, MA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One door spring was broken - the other was spring.
Instead of moving the unit out from under the counter, I did the job with the unit in place: (1) long reach to remove the old springs and attach the new ones to the frame at back of the unit, (2) use a loop of string to hook onto the other end of the spring, stretch it a little, and keep it stretched by hooking the other end of the loop to the screw that adjusts the unit's height, (3) slip the end of the cable to the front end of the spring and check to make sure that the cable is on its pulley, (4) take the string off the adjusting screw and wiggle it to free it from the end of the spring. (For comfort, lie down on a yoga mat when you do this job - thanks to my wife for this helpful suggestion!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert & Kathleen from FAIRFAX, VT
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door springs were stretched; with one broken
Followed the on-line tutorial. BINGO!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Left door spring had stretched and no l held the door upright
Opened the package and inspected the new spring
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Went to Part Select site to read directions
shut off the power
Reached under the dishwasher and disconnected the old spring from the frame
detached the old spring from the pulley cord
attached the new spring to the pulley cord
reached under the dishwasher and attached the new spring to the frame
Turned the power back on
total time around 15 minutes including reading the instructions
Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from WOODBURY, MN
- Parts Used:
- 8581548276014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from Grass Range, MT
- Parts Used:
- 5304507158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The top part of the lower spray arm got stuck on something a broke off the lower part of spray arm.
The are 2 tabs on the bottom of the lower spray arm that I pushed in and the arm popped right off. All you have to do is push the new spray arm on until you hear it snap into place, and you are done. It is really easy to do, and the part fit perfectly.
Was this instruction helpful to you?
Thank you for voting!