DW5900PW1 Frigidaire Dishwasher - Instructions

In about 20 minutes, I was able to remove the front panel and access the springs. Besides a hard water line in the way, it was a snap.

I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.

Removed the service panel below the door (4 hex-head screws), then reached in and took the old broken spring out (right side) and hooked the new one up.

Glad I bought 2 springs - the other one (left side) broke about a week after I fixed the first one! Replaced it the same way. Helps to have small hands - you can't really see where you're putting the springs but can feel where they should go.

The parts arrived 20 hours after ordering -great service & the parts were just like like the removed parts only new. The old door gasket was pulled from its groove & and the new gasket was installed witout using tools. No more leaking water.The door spring installation wesa bit more difficult. The front bottom was removed with a nut drive, the broken springs were fished out, new springs were pull onto the arms and the cover put back in place. Not a bad job for a crippled, one-eyed 82 year old man.

This could not have gone easier! As long as you get the proper parts it's a piece of cake. I wish everything was this easy!

Installed New rollers onto bottom rack. Part order & delivery were top notch from Partselect. Will definitely order from them again.

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

Fisrt, I opened dishwasher door. I then pulled out the lower rack & put new part in place and pushed in lower rack. Last, I closed dishwasher door.

merely snapped the part on

I ordered a new door gasket and door spring. I unscrewed the two screws that hold the dishwasher in place and pulled it out. I pulled the old broken spring off with pliers and installed the new one ,,,very easy. I then took the new door gasket and soaked it in hot water in the sink for 15 min. That made it very soft and pliable to work with. I used pliers to pull the old gasket out then cleaned the area around the old gasket where crud had built up. I pushed in the new gasket working from top to bottom one side at a time. Turned it on an ran through a cycle and it works perfect now ,,,no leaks.

Rollers just snapped on the diswasher rack. Took just seconds to do.

Simply remove the bottom panel below the door. The owners manual (22 year old model) showed the proper hole in which to attach the spring. Attach spring to door and then to frame of dishwasher, as illustrated in manual. It is a tight fit to get your hands in there, but once you do it is a snap. We have replace these springs several times over the life of this appliance, this is the first time we have actually found the proper springs, should last a long time. Thank you Parts Select for having the inventory for such an old model!

This dishwasher has a plastic bolt that holds the actuator on. The action loosens the bolt and it wobbles and eventually comes off. After enough attempts the bolt will strip and need to be replaced. I took some 3M loctite this time to hold it in place. It is 24 years old, but still kicking

2 wheels were missing and I replaced them in 2 seconds. The diagram online was a huge help!

Got the parts in a DAY! Wheels were broken and worn causing top tray to slip off runners- new wheels were easy to put in-used the screwsfrom the old ones and banged out the job in about 20 minutes, including letting my son help. Thanks Partselect, you've hooked a new DIY'er (my son)