GLD2161SCB1 Frigidaire Dishwasher - Instructions

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

Manually took off melted parts and replaced them with the new ones.

Removed old filters and trap and installed new ones.

I pulled out the internal filter and assorted washer parts. All in good shape. I bailed out the washer and removed the pump assembly from under the washer. I pulled it apart to inspect impeller. all looked fine. Plugged pump in and turned on pump cycle. Pump did not operate as it should have and I ordered new pump. My daughter put it back together and all is working well now!

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Simple repair.

I ordered the replacement pump from Partselect and it arrived 3 days later. The new pump went in very simply with two mounting screws (don't over tighten!!) and the two hose claps for intake and discharge. It works perfectly!

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

cleared water from machine with bulb type basting tool. Placed two large bath towels on floor in front of machine. Removed machine to floor laying it on the towels on its left side. Removed pump. Installed new pump. Reinstalled machine. Worked fine.

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

New right away when we heard the sound, the spring broke. Easy to replace, pull dishwasher out from under countertop, usually held in place by two screws into countertop. Remove screws, pull out dishwasher. Close door, springs will now have the most slack in them. One spring located on each side. Remove spring from one side and replace with new spring to ensure proper spring placement. No actual tools needed as spring rests on a bracket attached to door and other end of spring goes through hole in bottom of dishwasher rack. open door to test for tension as there are several holes to choose from. .

I just did the repair just like the video suggests to fix it. I disconnected the power cord, shut off and took apart the water inlet line, and drain line. Unscrewed the top of the washer from the cabinet and pulled out the dishwasher. Tilted the washer to better get to the bottom and took off the connecting wires (red and white.) Unscrewed the brass nuts holding the heating element and removed the element from the machine. Took out the bottom sprayer arm. Replaced the element, replaced the brass nuts and connected the wires back up. Put the sprayer arm back in. Pushed the machine back into place and re-secured the top to the cabinet. Hooked all water, drain, and power lines back up and all was good again.