FFID2426TD2A Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELIZABETH from ROANOKE, VA
- Parts Used:
- 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original part was damaged and dishes weren't clean
Removed 3 screws, swapped parts - done. Wonderful feeling and saved a service call. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from Cherokee, AL
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing a wheel on dish rack
just slid the wheel on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Racquel from Lake Charles, LA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FT LAUDERDALE, FL
- Parts Used:
- 5304500204
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water leak
watched a video, really easy fix. Solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Alamogordo, NM
- Parts Used:
- 140229954072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Top rack had rusted
Slid the rack out, removed the end pieces holding top rack in the sliding arms. Removed the spray arm. It was stiff & a bit hard to get off, but with a little careful prying it came off. Put that spray arm assembly back onto the new rack, slid the new rack back in place, put the end pieces back on and in less than 15 minutes, we were done. Part came in very quickly, I might add. I feel like I have a brand new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from ESTERO, FL
- Parts Used:
- 140229954072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusty and crumbled areas in upper dishrack
Just watch installation video. Finished repair in abut 30 minutes. Honestly, great service and fast delivery from this company. Please add the contact info to your favorites
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from MARINE ST CRX, MN
- Parts Used:
- 5304506521
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaked spot free fluid
Replaced part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from PORT ALLEN, LA
- Parts Used:
- 154844301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace dishwater pump.
Block and remove water hookup and drain hose. Ensure drain port on garbage disposer has a plug in it while drain hose is disconnected to ensure sink water does not find its way inside the cabinet. Place dishwasher with door facing floor. Remove electrical plug and pump retainer. Slide out pump. To replace pump reverse steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from COMSTOCK PARK, MI
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
My heating element was cracked
Remover the cracked heating element with the new heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from N ROYALTON, OH
- Parts Used:
- 154825001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The heating element (ring) showed signs of wear
I followed the steps on YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hank from Fort Pierce, FL
- Parts Used:
- 5304506521, 807145201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Making noise during operation.
Checked your videos and found the lower spray arm damaged (nubs worn down). Previous owner had some work done and didn't reinstall the parts properly. While during the repair, I also decided to replace the Detergent Dispenser and make a new spray shield. I guess the previous owner decided one wasn't needed.
Easy install, no noise.
Capt. Hank
Easy install, no noise.
Capt. Hank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DENVER, NC
- Parts Used:
- 5304507158
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lower arm broken,
Replaced lower arm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from MEDANALES, NM
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Sprang a Huge Leak
I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
PartSelect is a life saver and I saved lots of money by not having to call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from HAMPTON, NH
- Parts Used:
- 5304506916
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Two of the tub wheels cracked and broke off.
Unscrewed the old ones, new ones come with screw built in and recrewed the new ones in. So easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul J from LEXINGTON, MA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One door spring was broken - the other was spring.
Instead of moving the unit out from under the counter, I did the job with the unit in place: (1) long reach to remove the old springs and attach the new ones to the frame at back of the unit, (2) use a loop of string to hook onto the other end of the spring, stretch it a little, and keep it stretched by hooking the other end of the loop to the screw that adjusts the unit's height, (3) slip the end of the cable to the front end of the spring and check to make sure that the cable is on its pulley, (4) take the string off the adjusting screw and wiggle it to free it from the end of the spring. (For comfort, lie down on a yoga mat when you do this job - thanks to my wife for this helpful suggestion!)
Was this instruction helpful to you?
Thank you for voting!