FDB664RBR0 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jason from ERIE, PA
- Parts Used:
- 5300809611
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher was leaking from the front left corner. Gasket seemed bad on that corner by visual and physical inspection. Gasket moved quite a bit on that corner and not on the right side.
The repair was simple. When the part comes, you may need a hairdryer to heat up the plastic a bit to get any kinks that may have happened during packaging or shipping, very easy 5 minutes. Removed the old gasket by hand, very easy, 1 minute. You will need to clean out the track that the gasket sits in. Mine had years of black gunk inside of it. You will need qtips or a small screwdriver with some tissues or papertowels, easy but took 15 minutes to clean out properly. Installed new gasket in the track, start at the top middle, there is a notch on the gasket so you know where the middle is. Installed by hand, just push bottom edge into the clean track, easy 5 minutes. Ran the dishwasher with no leaks. Very pleased with the result and how easy the gasket was to remove and install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juergen from Shelbyville, IN
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door spring was broken
I removed the front panel below the door. There are 4 Hex screws, two at the top (accessible with the door open) and two at the bottom. After removing the screws, the panel came off, and I could reach inside to replace the springs. I found it easier to use a socket wrench than a screw driver.
Easily done. Anybody can do it. It took longer to clean up the panel than to do the actual repair.
Easily done. Anybody can do it. It took longer to clean up the panel than to do the actual repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Riley, MI
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old springs were broken
used the pliers to grip the end of the spring, extended it and removed it from the door and frame. The install then followed. It takes longer to remove the front panel than to do the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAWINDER from HOUSTON, TX
- Parts Used:
- 5300809611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water leak
Replaced the gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from McDonough, GA
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken door springs
very simple to do....attach spring to door...stretch to hole in frame and attach there...easy as 123
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Elkton, MD
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two wheels broke off
Snapped new wheels into place on the axel. New wheels were exactly like the old ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Longview, WA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken clip would no longer secure wheel
Snapped the new one in. One second repair - like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Los Angeles, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack got hung up & wouldn't roll
I snapped on the new roller and bingo! problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from Bryan, OH
- Parts Used:
- 5300809611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The seal in the door was broken.
I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Arvada, CO
- Parts Used:
- 5300809909
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
heard a noise while dishwasher was in operation, opened door and noticed the dishes were dry, no water was spraying out and dishwasher was making a whirling noise.
After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Pensacola, FL
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Spring broken, door hard to close.
I removed two screws that hold unit to countertop,
just pulled out unit about two inches. Removed broken door springs. Installed new door springs and pushed unit back into place and installed the 2 countertop screws DONE.
just pulled out unit about two inches. Removed broken door springs. Installed new door springs and pushed unit back into place and installed the 2 countertop screws DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Gurnee, IL
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Broken door spring
In about 20 minutes, I was able to remove the front panel and access the springs. Besides a hard water line in the way, it was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Duncanville, TX
- Parts Used:
- 5300809703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door spring broke
Removed the service panel below the door (4 hex-head screws), then reached in and took the old broken spring out (right side) and hooked the new one up.
Glad I bought 2 springs - the other one (left side) broke about a week after I fixed the first one! Replaced it the same way. Helps to have small hands - you can't really see where you're putting the springs but can feel where they should go.
Glad I bought 2 springs - the other one (left side) broke about a week after I fixed the first one! Replaced it the same way. Helps to have small hands - you can't really see where you're putting the springs but can feel where they should go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- denise from New Lisbon, NJ
- Parts Used:
- 5300809611
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water was leaking out of the door
I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Falls Church, VA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Half the wheels were missing from the lower rack.
So easy it shouldn't even count as a repair, really. The dishwasher, there when I bought the place, had a lower rack that wouldn't roll out as it should. That's because there were no wheels on the left side.
The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.
The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.
Was this instruction helpful to you?
Thank you for voting!