DW6250A1 Frigidaire Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Elkton, MD
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two wheels broke off
Snapped new wheels into place on the axel. New wheels were exactly like the old ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Longview, WA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken clip would no longer secure wheel
Snapped the new one in. One second repair - like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Los Angeles, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack got hung up & wouldn't roll
I snapped on the new roller and bingo! problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from East Stroudsburg, PA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken rack rollers
Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from Bryan, OH
- Parts Used:
- 5300809611
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The seal in the door was broken.
I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Arvada, CO
- Parts Used:
- 5300809909
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
heard a noise while dishwasher was in operation, opened door and noticed the dishes were dry, no water was spraying out and dishwasher was making a whirling noise.
After I received the Motor Shaft Kit I removed the spray arm tower and removed all screws, the center screw would not come out of the impeller, was stripped. Used a hammer and chisel to split the center of impeller and was able to remove. Also had to split the bottom impeller because it would not come out. All the parts that came in kit fit perfectly. Thank you Very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from Aptos, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
There were no wheels on the bottom rack of our dishwasher.
This could not have gone easier! As long as you get the proper parts it's a piece of cake. I wish everything was this easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell from Philadelphia, PA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken & missing wheels on lower rack
Installed New rollers onto bottom rack. Part order & delivery were top notch from Partselect. Will definitely order from them again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Metairie, LA
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
dishwasher was leaking at heating element connections
Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chaney from Batesville, AR
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing lower rack roller
Fisrt, I opened dishwasher door. I then pulled out the lower rack & put new part in place and pushed in lower rack. Last, I closed dishwasher door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Alpharetta, GA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke the wheel
merely snapped the part on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Greer, SC
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack rollers were missing
Rollers just snapped on the diswasher rack. Took just seconds to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Boonton Township, NJ
- Parts Used:
- 5300809611
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Worn out door gasket on dishwasher.
Removed old gasket and clean surfaces on tub and door before installing new gasket. New gasket has a small notch in the middle for top center. Install top then down sides for best results. Door gasket snaps into existing groove so no tools are required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Salisbury, NC
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
(leaking) heater element nuts cracked under dishwasher
power off, take off kickplate, unplug 2 wires and unscrew broken nuts, put new nuts on, plug wires back in,(run dishwasher one cycle to make sure no leaks) put kickplate back on, power on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Camarillo, CA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack difficult to pull out to load/unload
Thanks to PartsSelect exploded drawings, it was easy to identify and order the part. Installing was a case of just snapping it on the rack.
Was this instruction helpful to you?
Thank you for voting!