TUD6750RD2 Estate Dishwasher - Instructions

actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

Snapped the new stops on. It took about 2 minutes.

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

I had a broken spray arm on the dishwasher and though i would have to spend $450-$500 on a new dish washer, i ordered parts from part select(even though i was not 100% sure if it will work), the parts were shipped super fast and arrived in 2 days, i was able to replace the broken part and fix the lower spray arm. Part select saved me a lot of money.

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

when my package arived , I open the box and pop on my wheels, and all fixed in 60 sec. Thanks you saved me about 650.00 for a new Dishwasher. Thanks Melissa

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

First I read the other repair stories and knew it was a relatively easy repair. I removed the end caps on the front of the top dish rack and removed it for ease of access to the part. I then removed the two screws holding in the old part observing how it was positioned to make sure the new part was replaced in the same manner. I put the new part in place and screwed in place and replaced the dish rack. Everything is working just fine.

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.