TUD6710PT1 Estate Dishwasher - Instructions

Removed the lower spray arm assembly thumb screw and lifted off the spray arm assembly. The lower seal had disintigrated - couldn't even find any pieces in the filter. After reassembly with the new seal and bearing I turned the spray arm by hand to ensure it was not binding. There was still was, what I would consider, some excessive wobble. I fashioned a shim washer out of some plastic from a Folgers coffee can lid and installed it on the thumbscrew threaded shaft and tightened it all down finger tight - it works very well and now, and no wobble.
I relaced the upper spray arm seal while I was doing the job (both the upper and lower seals are the same part #). I figured it would go out on me eventually, so I might as well replace it while I was doing the lower arm work. Kept the old upper arm seal as an emergency replacement.

Cleaned the filter screen of all debris (it is amazing what collects there over time). Cleaned the stainless tub with some spray Greased Lightning, ran the rinse cycle, and then put a few tablespoons of citric acid crystals in the soap dispenser and ran the dishwasher on NORMAL WASH with temperature boost.
Looks new inside; cleans the dishes, glasses and utensils well (no water spotting); and is nice and quite (like when it was new).

Removed the washer from the cabinet, although the repair kit could have been replaced without this step. However, it still made it easier. Removed the spray arm assembly and the top cover to the motor. I had to block the motor to keep it from turning while I unscrewed part number 11. The rest was very self explanatory. The "impeller" was seized onto the motor shaft (20 years old) so I had to use a chisel to break what remained off, then clean some corrosion from the shaft. The repair kit worked and the pictorial parts diagram that came with the kit was very clear. Bottom line: "Easy peasy, lemon squeezy!" Great web site for diagnosis and parts diagrams!

repair was very easy did need to go to the hardware store for and adapter for the hose to water inlet valve as mine had a smaller diameter connector. Otherwise followed both videos. Needed a shopvac to remove water in the bottom of the dishwasher

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.

I bought the kit because it had other parts that I thought I needed.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!

It just snapped in placed. Very easy.

required NO tools,

just unscrew the large thumb screw, and replace the washer arm bearing!

problem solved like that!

maybe a 5 min job. part was a perfect match.

Removed seal from door with flat head screwdriver, replaced with new seal. Actually took longer to get out of the box rather than to fix!

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Note I did not have a model number just the manufacturer and name on unit. The website was still able to find the part. Impressive!
Easy installation. I recommend you also get the sprayarm seal. Be careful to insure the nut is seated securely before screwing in the nut. Highly recommend the video. Good company.

Just watched the YouTube video they recommended watching and it is very helpful. No tools needed and was finished in several minutes.