TUD6700PT0 Estate Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nathaniel from Chelsea, MA
- Parts Used:
- W10844024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Valve was leaking from plastic after water line change
Turned of water and unplugged the dishwasher.
Disconnected the incoming water line.
Drained on to the floor (have paper towels ready)
Disconnected the electrical feed wire.
Disconnected the rubber hose.
Unscrewed screw holding the fixture to the frame.
Took off the brass elbow from the old part.
Put pipedope around it and screwed into new part (carefully, so as to not crack plastic again).
Attached part back to frame.
Attached water lines.
Turned on water, plugged it in and ran dishwasher looking for leaks. No problem.
Disconnected the incoming water line.
Drained on to the floor (have paper towels ready)
Disconnected the electrical feed wire.
Disconnected the rubber hose.
Unscrewed screw holding the fixture to the frame.
Took off the brass elbow from the old part.
Put pipedope around it and screwed into new part (carefully, so as to not crack plastic again).
Attached part back to frame.
Attached water lines.
Turned on water, plugged it in and ran dishwasher looking for leaks. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pleasant Hill, MO
- Parts Used:
- WP8528862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leaking water out the front door.
replaced the two water defiector's, I had changed the door seal and should have changed the defiectors at the same time. Save yourself some time and ordor both parts. This is a easy fix, anyone can do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Arley, AL
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
O ring seal was streched out allowing a leak
Removed 5 or 6 screws replaced O ring,Srewed cover back on ,no more leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Wharton, TX
- Parts Used:
- W10844024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench set
No water coming into dishwasher
I unscrewed the old water inlet valve from the frame of the dishwasher so that I could manuever my hand around to the backside where the rubber hose was connected. That was the easy part. I then had trouble holding the old valve while trying to unscrew the hot water copper tubing so I screwed it back on the frame. My dishwasher is close to 18 years old and I think that was part of the problem. After soaking in WD40, I finally got the valve out. Then I had to remove the "L" shaped connector to put on the new valve. Everything went back together a lot faster and it's like I have a new dishwasher again. By the way, I am a 53 year old female so that may be why it took me so long.
Was this instruction helpful to you?
Thank you for voting!
Water leak from center of motor unit
Removed dishwasher, take to garage, removed lower rack to gain access to top of motor unit. Used star socket wrench to remove upper screws holding top of unit in. Disconnect wires, drain tube and counter weight. pulled motor unit out from inside dishwasher and placed on bench. Proceeded to disassemble motor. Some things were obvious, others not so. replaced old worn out parts with new, used a little lube (Vaseline) in places to assist in getting seals back in place. Instructions were of little help need to pay close attention when tearing unit apart. Reassembled with new seals, installed motor and re-installed dishwasher...NO LEAKS!! Wife and I happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from St. Louis, MO
- Parts Used:
- 3378149
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
Latch broke on Dishwasher
Had to pull the dishwashwer out to replace the latch. Did this by unscrewing the 2 screws that hold the Dishwashwer to the under side of the counter. Dishwasher then pulled out easily. Then unscrewed to screws on the latch. The screws were accessed by pulling out the modling/strip around the dishwasher door. Also easy to replace the screws. But sliding it back in was a little harder. Had to shorten the front legs on the dishwashwer to get the back of the dishwasher to go back in. Then screw the front legs back out. Finally re-inserted the screws under the counter that attached the top of the Dishwasher to the counter top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from BURTONSVILLE, MD
- Parts Used:
- WP661566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
No heat. Replaced thermostat
Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Holbrook, AZ
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
dishwasher leaks from left side of door
The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHANE from Dunkirk, NY
- Parts Used:
- WPW10509257
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher leaked
first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Germanton, NC
- Parts Used:
- WPW10509257, WP8528862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish Washer was leaking badly
Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from pine river, MN
- Parts Used:
- WPW10204131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the axels for the wheels of therack adjusters deteriated
replaced the rack adjusters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Clarksville, TN
- Parts Used:
- W10844024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
inlet valve cracked
I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brendan from SARATOGA SPGS, NY
- Parts Used:
- WP661566
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
My dishwasher's heated dry cycle wasn't heating up
After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from FAYETTEVILLE, NY
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost stop from one side of top rack. Rack could be pulled off track.
Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from cambridge, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher was overflowing
actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.
Was this instruction helpful to you?
Thank you for voting!