EIDW5905JB0A Electrolux Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary Pat from CAVE CREEK, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of Silverware gone,silverwear went to bottom of dishwasher
Your service was great, the basket came in two parts and all I had to do was put the two together and put it in the dishwasher. I am glad we were able to get a new one. Thanks again for such quick service. Thank you very much for such great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from AURORA, IL
- Parts Used:
- 14005493802, 5304532950, 154740304, 154428402
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Some rack components were rusted and broken. Replacement was necessary.
Repair was easily performed by removing old parts and snapping new ones into place.
I woulsugest that you take a picture before removing the old parts so that you can correctly orient the new ones.
I woulsugest that you take a picture before removing the old parts so that you can correctly orient the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from STURBRIDGE, MA
- Parts Used:
- 5304532969
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Parts rusting
Open door, Lift out old ,replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert C from COTTONWOOD, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old basket developed holes and needed replacing.
Took the old out and placed the new in its place. That simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mena from Sarasota, AL
- Parts Used:
- 5304535382
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cutlery basket
Simply took the old one out, and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from QUINCY, IL
- Parts Used:
- 5304532969
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack was rusting
replaced works better one way than other wheels fall in door slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- oscar from WOODBRIDGE, VA
- Parts Used:
- 5304507354
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken lid of the detergent dispenser.
The video show a different model, the only difference is that the screws for the top part shouldn't be removed only the ones that hold the front. Replace the detergent dispenser once the cover is removed is easy. All works like brand new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lorton, VA
- Parts Used:
- 5304507354
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rinse aid dispenser leaking and empty after 4 wash cycles
Needed to replace detergent / rinse aid dispenser unit on the inside top of door.
1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.
2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.
3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.
4) Position new unit through interior. Screw in place.
5) Re-attach four (4) wires in same sequence as disconnected.
6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.
2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.
3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.
4) Position new unit through interior. Screw in place.
5) Re-attach four (4) wires in same sequence as disconnected.
6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from EAST ISLIP, NY
- Parts Used:
- 5304532950
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A piece of the upper rack began to rust out
Used the screwdriver to pry the upper rack left side tine up and out. Slipped the new one into place and pressed hard to seat the tine. this process took all of about 20 seconds to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- S from ROHNERT PARK, CA
- Parts Used:
- 154740901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Removal handle had broken off making it hard to remove and clean trap.
Once replacement part arrived removed old broken item and snapped in new replacement item. Much easier to clean now. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from COTTAGE GROVE, OR
- Parts Used:
- 14005493802, 5304532950
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Rusted out parts
Replacement parts installed. Very easy to snap in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from HOPATCONG, NJ
- Parts Used:
- 154859401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The sensor showed an E1 leak which is "water underneath the machine"
Went to the website, viewed the schematic and ordered the two gaskets that form the seal around the door and tub, Gaskets should be ordered as a set if you have a leak and suspect the door. We saw discoloration at the bottom edge of the tub gasket indicating that there was water seeping through out onto the floor.The gaskets install by hand without the use of tools. Less than $100 in parts prevented the replacement of a $1,400 dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VERSAILLES, KY
- Parts Used:
- 5304507354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Would not dispense dish washing tablets
Turned power supply off to dishwasher Opened door and removed screws holding font of door Unplugged soap dispenser and removed six screws. Popped out and installed new dispenser. Plugged wires into new dispenser and installed front of door. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Gladstone, OR
- Parts Used:
- 154428402
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The brackets on the lower rack had worn out and not holding up the tines.
The parts came in a timely manner and took about 15 minuets to replace with no tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIMOTHY from ELBURN, IL
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old basket had a hole
Lift out old basket replace with new basket
Was this instruction helpful to you?
Thank you for voting!