FDPH4316AD Electrolux Dishwasher - Instructions

Nothing to it. Just inserted the iron stud into the center wheel and pressed the bracket onto the stud.

I woke up on Christmas Day to water pooling under the kitchen sink (I guess I made the naughty list last year). Upon inspection, I could see that the water connections for the faucet were damp. Since I had all the parts, I replaced the faucet and service lines. Once complete, there were no leaks so I turned on the dishwasher to double check for leaks in those lines. It was all dry when the dishwasher finished but the next morning, more water under the sink.
I proceeded to replace the water line to the dishwasher and ran it through another wash cycle. Still leaking.
I found PartsSelect online and order a new drain line for the dishwasher. To my amazement, FedEx dropped off my order the next morning........yes, the next morning.
It took five minutes to remove the old drain line and install the new one (just a worm clamp at each end). It would have been faster than that but I don't get up and down as fast as I use to.

on close investigation the problem was not the element ,but one of the brass nuts was fractured this was repaired and leakage was rectified. I .would add that your service and delivery was excellant and the unrequired element will be returned to you thanks

Pulled out the gasket,trimmed the gasket to fit and alittle pressure to put.it in place, very easyto do. No worries any one can do this and savek yourself costly repair person.

After reading some "Suggested Installation Instructions" on the Parts Select Website, I felt at ease tackling this job. After opening the door, I simply pulled-out the existing door gasket. The installation involved simply pressing in the new gasket with my finger and insuring it was properly seated. The only tool I had to use was a pair of scissors to cut the excess length as I pressed it in. REALLY APPRECIATED THE SIMPLE INSTALLATION INSTRUCTIONS as I had never done this particular task.

Removed old gasket,placed new one on pressing into place.Very quick and easy.Saw the youtube on how to do it.Unfortunately this was not the problem.now have a new dishwasher same brand.

Spotted the source of the leak at the first heating element under the dishwasher. Removed the brass mounting nut and it was cracked. Replaced with new part from PartSelect.com and the leak was fixed. Apparently the heating element gets so hot it tends to crack the mounting nuts, which results in a leak. Delivery time for part said 3-5 days - mine arrived one day after ordered!

pULLED THE WASHER FROM THE COUNTER disconjnected the house from the garbage disposal connected thenew hose to the disposal, remove other end of old hose from thedishwasher and replace with the new drainage hose.

Disconnect drain hose, disconnected power, laid dishwasher on its back. Had to remove wash motor, then had access to the drain pump. Removed bad drain pump, installed new drain pump, reinstalled wash motor, reconnected drain hose, then reconnected power. Job is done working as intended. Really easy.

I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!

I already had the dishwasher removed for remodeling. I wrecked the drain hose myself. When I received the replacement it was a breeze to install.

The hose goes from the water inlet solinoid to the side of the dishwasher.Remove the kick plate from the bottom front of the dishwasher. Disconnect the water supply to the inlet of the solinoid valve (copper tubing on mine). Remove the screws under the counter top which hold the dishwasher in place. slide the dishwasher out from under the cabinet only as far as needed to expose the hose(about 1 foot). The hose is behind the insulation. Remove the hose clamps from both ends of the hose(solinoid outlet and side of dishwasher)Remove hose carefully because this is all plastic. Install replacement hose and clamps. The new hose is several inches too short and will not fit into the upper hose guide, just bend it underneath. Be sure to put hose in lower keeper on side of dishwasher. Attach clamps, tape insulation back in place, slide dishwasher back under counter and install screws under counter. Attach copper tubing to water inlet solinoid valve. Run dishwasher and check for leaks. Replace kick plate. Note: I had enough loose electrical wire to slide my dishwasher out. If you don't have enough wire to slide out the dishwasher you should call a repair man.

After looking at several youtube.com remedies, I zeroed in on the problem... non-functioning waste water pump. I also noted that the valve flapper was in rough shape so ordered both. Once I got the new parts, I replaced the old ones in less than 30 minutes. When I removed the old pump assembly, I discovered that the four-blade waste water wheel had broken off. For about $75, I repaired what no one in my small rural town could. I think the retail on the dishwasher was somewhere between $300-350, so I figured it was a good deal. Also I scored BIG man points with my wife!

All I have to say is paets select is the best company I have delt with in the last 20 years

Purchased new drain pump thinking that was the issue. When I was installing I noticed the drain hose was clogged. Since the way out cabinets were installed by the previous owner getting the dishwasher out is a little more complex so installed the drain pump and drain hose just to make sure. Runs like new!