CDB350NB9B Crosley Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from DOTHAN, AL
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower swivel arm broken
Unsnap old and snap on new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Milford, MA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish washer leaking at the door
Pulled off the old gasket and replaced it the same way with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from Sacramento, CA
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Leaking from Bottom of Door
Replacing the part was easy. Just pop the old one out and pop the new one in. This item fixed my leaking door problem. The old arm had fallen against the heating element, which burned a hole through the end. Water was shooting out that hole and leaking under the bottom door seal. Replacing the door seal did not help, but replacing the arm fixed the leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yangde from Raritan, NJ
- Parts Used:
- 154430501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door springs were broken and the dorr was very heavy to open and close.
I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erinn from FINKSBURG, MD
- Parts Used:
- A00126401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Wouldn't drain
Pulled the dishwasher out, rolled it onto its right side, removed the old pump by removing the 2 electeical connectors and 3 #20 torque screws, and replaced the pump. The most annoying thing was it dumping water on the floor. The rest was relatively easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MARSHALL, MI
- Parts Used:
- 5304523457
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
Water inlet tube had worn a hole in it
Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BAY SHORE, NY
- Parts Used:
- 154430501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Spring broke
Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from BELLEVILLE, IL
- Parts Used:
- 5304512731
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No power. Power surge took out the whole board
Just so simple take out the Phillips screws take off the cover three screws hold on the board. Un plug the connectors place the new board in and replace the screws. Simple plug and play.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SHICKSHINNY, PA
- Parts Used:
- 154844301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Faulty pump
Replacement was every bit as simple as the website said it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynda L from BRIGHTON, MI
- Parts Used:
- 5304500204
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
leaked at the bottom of door.
My brother in law installed it for me. There was some difficulty finding the right angle but once we realized we needed to start at the very right side it went well. So far no more leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from NEW KENSINGTN, PA
- Parts Used:
- 5304506525
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Replace filter in dishwasher
Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from FARMINGTON, NY
- Parts Used:
- 154844301
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Pump motor kit
Pump motor kit changing the pump went good little tough to get the old one out And the new one went in a little tough really had to push hard to get it in but it works great took longer to take out the dishwasher and put it back in instead of changing the actual part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from FREEHOLD, NJ
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Edge metal broke away from the melted tabs
The original lower spray arm had one end break loose the metal retainer end. I used a temporary small hose clamp to fix as I waited for the new lower arm to arrive.
The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.
The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Woodburn, OR
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking at the front, just below the door
I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lora from Shelter Island Heights, NY
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking underneath dishwasher
My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!
Was this instruction helpful to you?
Thank you for voting!