CDB350NB4A Crosley Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Loren from Sacramento, CA
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Leaking from Bottom of Door
Replacing the part was easy. Just pop the old one out and pop the new one in. This item fixed my leaking door problem. The old arm had fallen against the heating element, which burned a hole through the end. Water was shooting out that hole and leaking under the bottom door seal. Replacing the door seal did not help, but replacing the arm fixed the leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fort Washington, MD
- Parts Used:
- 154662601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher door strike piece broke. Door had to be propped closed each time dishwasher was used.
Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from La Mirada, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from PENTWATER, MI
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower sprayer arm melted after being lodged
Pulled the old one off and pressed the new one on (plastic clips hold it on). Dishes much cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from West Bloomfield, MI
- Parts Used:
- 5304512731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwaser just would not start. Indicator light were flashing.
Figuring the issue was the Control Board, I ordered one. ($90) When it came I installed it...SAME problem. So I took it out and reinstalled the old board and it WORKS. Apparently some connection was not right and just moving the conectors by taking them in and back out twice fixed the problem. And FYI, since it is an electric part it is NOT returnable once it s been installed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lora from Shelter Island Heights, NY
- Parts Used:
- 154106202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking underneath dishwasher
My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Woodburn, OR
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking at the front, just below the door
I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynda L from BRIGHTON, MI
- Parts Used:
- 5304500204
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
leaked at the bottom of door.
My brother in law installed it for me. There was some difficulty finding the right angle but once we realized we needed to start at the very right side it went well. So far no more leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TITUSVILLE, FL
- Parts Used:
- 807117001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Need a new draqin hose
Easy
Was this instruction helpful to you?
Thank you for voting!
Plastic had melted on the screw
Eventually broke off old heating element to get it out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHAMBERSBURG, PA
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The dishwasher wasn't cleaning the dishes
I rolled the lower basket out of the way, lifted the spray arm up and out. Then I located the replacement part on Frigidaire's website and placed the order. The part came quickly and I snapped it into place. No tools required. Now my wife is happy and so am I.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from KENDALLVILLE, IN
- Parts Used:
- 5304506517
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Replacing grommet
Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reynaldo from ORANGE PARK, FL
- Parts Used:
- 5304500204, 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leak
Removed all sealer and install new one as instructed.
Was this instruction helpful to you?
Thank you for voting!
the nut holding on the element would not tighten. leaked at the location where the nut was located
Removed the cover at the front bottom to gain access to the nuts holding on the element.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.
Turned off dishwasher breaker.
Removed the wires connected to the element.
With a 1/2" wrench, removed the element mounting screws.
Removed the bottom rack.
Removed the lower spray arm.
Removed the element from 2 clips.
Removed the element.
Put the new element in place.
Clipped it in.
Put new screws on and tightened up with a wrench. Not too much but enough to squash the washers to make a tight seal.
Replaced wires.
Replaced spray arm and bottom rack.
Turned on the breaker.
Ran it through a cycle to check for leaks.
Replaced bottom cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from OAKLEY, CA
- Parts Used:
- 5304535380
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Changed out upper rack
Replaced upper wash blade and used screwdriver to pop off rail stops to slide rack all the way out to exchange
Was this instruction helpful to you?
Thank you for voting!