CDB500NB0A Crosley Dishwasher - Instructions

Pump motor kit changing the pump went good little tough to get the old one out And the new one went in a little tough really had to push hard to get it in but it works great took longer to take out the dishwasher and put it back in instead of changing the actual part

i just took off the old and poped on the new, it was way to easy! no tools required!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Although the part I ordered was not an exact match, it was a Frigidaire piece and fit onto the spray arm assembley the same way. And if I do say so, it actually seems to clean the dishes better! All I did was clip the new one into place.

Easy repair. pulled dishwasher out, disconnected electrical wire for safety but don't think it was required since the breaker was off (turn it on and flip the breaker for verification). Pulling the pump and replacing was easy, soap dispenser, same, easy. First time I ever worked on a dishwasher, simple. Parts were all OEM parts and most importantly were the correct parts I needed. Way cheaper than replacing the unit and I saved $150 on an hours worth of work vice paying the service guy.

Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.

I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.

1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!

Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy

Unscrewed the housing for the old piece and screwed on the new part. No tools needed. Easy to use website, fast delivery. Very easy.

The Inlet valve was leaking. I removed the old valve in less than 30 min.Note: need bright flashlight! It could have been quicker but I had to lie on the floor and squeeze my big hands under the opening (kick panel). Once I got the two small bolts out, I was able to manipulate the valve out from under the dishwasher, then I carefully removed the two lines. I received the part in 5 days and installed it in 45 minutes. It could have been a faster installation, however I was not about to pull out the whole dishwasher. Again, I was able to manipulate the new valve back in & tighten then test everything.(note: need a bright flashlight to see underneath) I immediately ran a load of dishes and Presto! No leaks and runs like a Swiss watch!

Easy as pie. Just turned off water and electricity. Disconnected hoses and wires and replaced with the new valve.

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

It only took about 20 minutes to replace. Thanks for the video.

Ordered the parts, put into place and that was it...very easy...had to undo the upper rack spinner wash blade but was easy to remove and put back onto the new rack...