CDB500NB5B Crosley Dishwasher - Instructions

I left the unit in place. I removed the bottom cover, unplugged power from GFI receptacle and closed water supply valve. I unplugged the electrical connection. I put a dishtowel under water inlet valve and removed water supply. I removed two screws from inlet valve bracket that allowed me to rotate the valve and used pliers to remove water hose clamp and hose. I installed the new valve in reverse order. I checked for leaks; found none. Life is good again!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Although the part I ordered was not an exact match, it was a Frigidaire piece and fit onto the spray arm assembley the same way. And if I do say so, it actually seems to clean the dishes better! All I did was clip the new one into place.

i just took off the old and poped on the new, it was way to easy! no tools required!

Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.

VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.

I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!

Unscrewed the housing for the old piece and screwed on the new part. No tools needed. Easy to use website, fast delivery. Very easy.

My husband and dad actually did the repair, but my husband not being a handy guy said it was, 'so easy, anyone could do it!' He was very nervous about taking on the project, the longest part was testing to make sure it worked(running a cycle).
The simply pulled out the dishwasher, after disconnecting all electrical power, drained the rest of the water that we couldn't see from above, following the video given took out the old part without needing to take out the motor and were able to replace the drain pump, put everything back together besides sliding it into place in case it didn't work, in less than 15 minutes! When the short cycle finished and the water had drained they put it back into place and ran an energy saver cycle and it worked like a charm! Since then(2 weeks ago) we have now ran every function and have had no issues! Every time we open the dishwasher we comment on how much we missed having a dishwasher! Haha!

1-2-3 snapped off the old and snapped on the new! New part was just as ordered and just like original! My dishwasher is like new again! Thanks PartSelect for your great price and prompt shipment!

It only took about 20 minutes to replace. Thanks for the video.

Ordered the parts, put into place and that was it...very easy...had to undo the upper rack spinner wash blade but was easy to remove and put back onto the new rack...

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

Most of the time is spent cleaning out under the sink, turning off water valves, disconnecting hoses and collecting water. One valve did leak when closed. Then pull out the dishwasher from under the counter, unplug and lay flat on floor.
Disconnect power from pump. Remove 2 screws and bracket that holds pump in place, gentle twist and pull out pump. Place tow gaskets around pump. Wet gaskets and gently push pump in place be sure to line it up so bracket goes back in place. Tighten screws, put hoses back in place, push dishwasher back, connect hoses, open valves, check for leaks then run the dishwasher and check operation of pump. I recommend viewing replacement on part select youtube video to determine if you can make the repair.

First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!

I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.