CDB900NS3A Crosley Dishwasher - Instructions

Took me about 2 minutes to repair, no tools to repair, very easy installation repair!

Easy fix but not cheap
replaced drain trap and four rack wheels with clips

All parts were expensive for the items.
found cheaper wheels w/clips for much less on another site.

Replacement was every bit as simple as the website said it would be.

Removed screws for door panel, then literally 2 screws to change out the latch!!

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.

I removed the bottom drawer and glass trap in order to remove the old melted down washer arm. Once those parts were removed I was able to easily secure the new replacement be ensuring that it was turned enough and fit down securely (side note, if you don't hear the arm click or snap into place, it isn't secure). The part works just fine, but sadly I think I have another problem with my washer, but I will figure it out.

The original lower spray arm had one end break loose the metal retainer end. I used a temporary small hose clamp to fix as I waited for the new lower arm to arrive.

The design is very easy.... pull up on the OLD and then just push DOWN on the new arm into the bottom.

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

Pump motor kit changing the pump went good little tough to get the old one out And the new one went in a little tough really had to push hard to get it in but it works great took longer to take out the dishwasher and put it back in instead of changing the actual part

It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.

Had to shut electricity off and turn water off and disconnect them both. Take the screws out from underneath the counter. Slide out the unit disconnect the filler tube in the back disconnect the hose and replace and repeat the process to put it back together.

Eventually broke off old heating element to get it out

Excuse me, as I do not know all the correct nomenclature, but I hope you get what I am saying. The new spray arm would not thread on to my dishwasher water supply coming out of the top of the box. Every time I would try, the supply line would push back up into the housing. Probably need to fix that too, but then I would have to uninstall the DW and just don't have time for that. My old part would thread right on, no problem, but the connection holding it all together was wore out. So I took the new arm and the old "nut" and put them together. They threaded right on, I pulled down on the arm and it is secure. So I had to Frankenstein it a little, but my DW is working, I didn't have to tear it apart and reinstall it, and I didn't have to replace it. Win Win!

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg