CDBEH950SB1A Crosley Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Milford, MA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dish washer leaking at the door
Pulled off the old gasket and replaced it the same way with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elner from new concord, KY
- Parts Used:
- 5304506516
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic piece that held the arm on was worn & dishwasher only 2 yrs old.
Arm screwed on and immediately fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reynaldo from ORANGE PARK, FL
- Parts Used:
- 5304500204, 154827601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leak
Removed all sealer and install new one as instructed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Keota, OK
- Parts Used:
- 5304525218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water did not drain. Found the door latch broken
Unplug dishwasher. Open the door. Remove two Phillips head screws holding the door panel on. Slide door panel down and out to remove. With door still open, remove the six T20 torque screws that hold the control panel. Behind the control is the latch assembly. Take a picture of the wires going into the latch assembly for installation reference(mine was black wires on left and white wires on right). Unplug the two sets of wires. Remove two T20 torque screws that hold the latch. Replace with new latch and reverse steps for installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERTA from FAIRBANKS, AK
- Parts Used:
- 5304532229
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
wheels break or bend or fall off
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert C from COTTONWOOD, AZ
- Parts Used:
- 5304535382
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old basket developed holes and needed replacing.
Took the old out and placed the new in its place. That simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex from COMMERCE, GA
- Parts Used:
- 5304500204
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom door seal leaking on my dishwasher
Still have a slight leak, but I'm thinking it may just need time to seat itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FAIRHAVEN, MA
- Parts Used:
- 5304525218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door wasn’t locking
You tube video and it was so easy less than 20min had it fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from La Mirada, CA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking Dishwasher
The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from PENTWATER, MI
- Parts Used:
- 5304517203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower sprayer arm melted after being lodged
Pulled the old one off and pressed the new one on (plastic clips hold it on). Dishes much cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhiannon from FEDERAL WAY, WA
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old sprayer arm melted to heating coil.
Easiest repair EVER!!! You just pull the old spray arm off (be sure to keep all the smaller pieces that click it into the bottom of dishwasher) and pop the new one in. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from DOTHAN, AL
- Parts Used:
- 5304517203
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower swivel arm broken
Unsnap old and snap on new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SHICKSHINNY, PA
- Parts Used:
- 154844301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Faulty pump
Replacement was every bit as simple as the website said it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SUNBURY, PA
- Parts Used:
- 154579101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
the end on one of the door springs on the dishwasher broke off
I removed the access panel using a nut driver. One fastener on each side at the lower front panel. Move the two piece lower panel and set aside. Locate the broken spring. It will be on the floor under the dish washer. Remove the broken spring. Place the new spring end in the hole in the chord end and place the chord over the plastic guide. Use a pliers to stretch the spring and fasten it to the hole in the lower dishwasher frame at the back of the dishwasher. Check the door for proper tension. Replace the lower panel and secure with the two screws. I recommend replacing both springs at the same time to insure proper balance. If you only replace one spring you will be replacing the other in the near future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynda L from BRIGHTON, MI
- Parts Used:
- 5304500204
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
leaked at the bottom of door.
My brother in law installed it for me. There was some difficulty finding the right angle but once we realized we needed to start at the very right side it went well. So far no more leaks.
Was this instruction helpful to you?
Thank you for voting!