CDBEH950SB1A Crosley Dishwasher - Instructions

I went to your website found part# and parts diagram and ordered parts . I picked standard shipping . That evening e-mailed me they were instock and shipped also gave tracking # thet parts were here the next day.I removed the front dec panel then the 4 nut& bolts holding door to hinges(with door in closed position).Then I removed the 2 screws holding the hinges to the frame/axle. Replaced hinges with new ones .Put screws back in frame/axle . Put 4 nut and bolts back to secure door to hinges . Then i reinstalled under counter put new wheels on lower rack . I then filled it with dishes and ran a long cycle checked for leaks THEIR WERE NONE!!! THANK GOD !! Job complete, Thanks parts direct for a well designed website and detailed pics and parts#. TIM

Turned power off , shut the water off to washer , unhook water line , unhook drain line from sink drain , unplugged electric chord from the wall . Open the door look where the door latches you'll see two metal strap' s that are screwed under the counter . Take the screws out . Take the bottom basket out .Take the spray bar off . There's two clips on the bar just push them out lift bar up .There in the middle of the washer you'll see filter screen. There's a small handle looking thing do not know what they call it .lol Twist one way or the other to take it off . Once you have that out of the way take the three screws out mine were hecksscrews .Pull the cover off remove the ball . Take a rag and take the excise water out in the bottom . Pull the washer completely out from under the counter . Lay it on the back side on the floor . You'll see the pump it has U shape metal holding it with two screws . Take the to screws out remove the U shape metal bracket . Unplug wire going to motor squeeze the clip and pull . Twist motor back and fourth and pull slightly till it comes out . Put new O rings on new motor and lubricate O rings and slide motor back in . Reverse the process . Take pictures if you need to as your taking things off if your afraid you won't remember.

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

Easiest repair ever. Part came quickly & came fully assembled. Just screwed the part on by hand and it has worked like new ever since. The original part is 3 separate pieces but the new part was all in one & fit perfectly.

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

found spray arm on the rack looked at the top of rack saw a nut screw the nut looked at the clip found the ears broke off easy r&r.

Simple repair.

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Slid dishwater out from cabinet, replace cable, slid unit back in , secure ---done! door has tension now.

Removed screws for door panel, then literally 2 screws to change out the latch!!

Removed all sealer and install new one as instructed.

First let me say I love this company, I have used them before and I will use them again.
Parts arrived quickly, unwrapped them, put the video
supplied by this site on my phone and the entire project was done in less than ten minutes. My dishwasher works like new. Thank you !

Takes longer to open the machine and remove the lower basket than to do repair.

Snap arm and support together, align and twist in machine to lock in place.

Save yourself some time and buy the support. High risk it can be broken while being removed from the arm. I am glad I purchased a new one and didn't take the risk.

Replace the latch. Got to cut off old latch, trim wires, install latch, and put on the dishwasher door cover back on with screws

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.