CDU400B Crosley Dishwasher - Instructions

Ordered new part from your site. The new basket arrived in just a few days, without the handle and cover for the small item section. Instructions with with new basket described how to remove the other parts from the old basket and install them on the new one. Everything worked out perfectly and my silverware stays put. I've very happy!!

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

The problem is a worn seal ring. That ring is inside the lower spray arm's spray nozzle support assembly. The wash arm spins on that assembly.

I unscrewed the lower spray nozzle popup, from the wash arm support. That part, from which the extending spray nozzle rotator pops out, simply unscrews, by hand, from the wash arm support. Then I could lift off the wash arm itself to get it out of the way for the next step.

With the wash arm removed, I could then gently pry off the flat filter cover which was underneath the wash arm (the filter cover is simply clipped on. Use a screwdriver).

Now, reaching inside where the that popup spray nozzle was screwed on, you can see and/or feel a tall skinny plastic piece in the center of it, which actually screws that wash arm support onto, well, the rest of the dishwasher.

With that "screw" removed by hand, I removed the wash arm support.

Inside that wash arm support the old ring seal can be removed and the new one inserted.

Simply reverse the process to re-assemble.

Note that it's hard to determine where, exactly, to put that ring seal, inside the wash arm support. But it seemed to me it didn't really matter as long as it was just in there.

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

Once I removed the inside panel from the door replacing the switch was pretty simple. completed the job in less than twenty minutes.

This was the third appliance I have repaired with the help of Parts Select in the last three months.

First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.

Thanks to all the previous posters for their hints.

I removed lower cover panel. Removed two wires. (one on each end of the element. Removed two nuts on the element. Took out old part. Put new part in and reversed procedure. Works fine now.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

I had to take the complete builtin dishwasher out of the base cabinet in the kitchen.

turn off electricity - circuit box
turn of water supply - turncock under sink
remove kickplate - screw driver
disconnect electric wires - screw driver
disconnect water feed - 5/8 wrench
remove top screws at counter underside - screw driver
pull out dishwasher - hands and son
turn dishwasher upside down - hands and son
got some water on floor - towel to mop up
remove top shower hose ( a rigid pipe with a screw fitting at top and a neoprene coupler at bottom) - hands
The neoprene coupler is the part that failed, it had worn thin due to heavy water flow

reverse process - same tools

voila - no water leak

I replaced a Silverware basket at the same time, which took two mintues as I had to remove the handle from the old basket and press fit onto new one - hands

Parts Select had the parts I needed and delivered in less than 48 hours. That is great service.

My husband thinks I'm the smartest wife ever! He's telling all his friends how I got online to research the problem (thanks to your readers and DIY comments!), diagnosed it, ordered the parts and - voila - clean dishes once again! It's like everyone said, remove inside of the door by removing 7 torx screws, dismantle wiring -remember to note what connects to what - pop out old parts, easily insert new ones (that arrived in record time!), reconnect wiring, replace door and you're done. Replacing the reservoir o-ring also stopped the leaking problem that preceded the door issue. Thanks PartSelect!

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

Removed old gasket and simply replaced it with the new one. Very easy.

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~