CDB400KW0A Crosley Dishwasher - Instructions

Easy

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Although the part I ordered was not an exact match, it was a Frigidaire piece and fit onto the spray arm assembley the same way. And if I do say so, it actually seems to clean the dishes better! All I did was clip the new one into place.

i just took off the old and poped on the new, it was way to easy! no tools required!

I removed the screws from the inside of the door. There are also tiny screws you have to remove that holds the part onto the door. Then I was able to remove the part, unplug the power receptacles and install the new part. Very simple!!

Turned power off , shut the water off to washer , unhook water line , unhook drain line from sink drain , unplugged electric chord from the wall . Open the door look where the door latches you'll see two metal strap' s that are screwed under the counter . Take the screws out . Take the bottom basket out .Take the spray bar off . There's two clips on the bar just push them out lift bar up .There in the middle of the washer you'll see filter screen. There's a small handle looking thing do not know what they call it .lol Twist one way or the other to take it off . Once you have that out of the way take the three screws out mine were hecksscrews .Pull the cover off remove the ball . Take a rag and take the excise water out in the bottom . Pull the washer completely out from under the counter . Lay it on the back side on the floor . You'll see the pump it has U shape metal holding it with two screws . Take the to screws out remove the U shape metal bracket . Unplug wire going to motor squeeze the clip and pull . Twist motor back and fourth and pull slightly till it comes out . Put new O rings on new motor and lubricate O rings and slide motor back in . Reverse the process . Take pictures if you need to as your taking things off if your afraid you won't remember.

Most of the time is spent cleaning out under the sink, turning off water valves, disconnecting hoses and collecting water. One valve did leak when closed. Then pull out the dishwasher from under the counter, unplug and lay flat on floor.
Disconnect power from pump. Remove 2 screws and bracket that holds pump in place, gentle twist and pull out pump. Place tow gaskets around pump. Wet gaskets and gently push pump in place be sure to line it up so bracket goes back in place. Tighten screws, put hoses back in place, push dishwasher back, connect hoses, open valves, check for leaks then run the dishwasher and check operation of pump. I recommend viewing replacement on part select youtube video to determine if you can make the repair.

The Inlet valve was leaking. I removed the old valve in less than 30 min.Note: need bright flashlight! It could have been quicker but I had to lie on the floor and squeeze my big hands under the opening (kick panel). Once I got the two small bolts out, I was able to manipulate the valve out from under the dishwasher, then I carefully removed the two lines. I received the part in 5 days and installed it in 45 minutes. It could have been a faster installation, however I was not about to pull out the whole dishwasher. Again, I was able to manipulate the new valve back in & tighten then test everything.(note: need a bright flashlight to see underneath) I immediately ran a load of dishes and Presto! No leaks and runs like a Swiss watch!

Easy as pie. Just turned off water and electricity. Disconnected hoses and wires and replaced with the new valve.

Used pliers to remove old seal. Keep seal in position, note the notch facing the hole. Align the new seal, press it in, the notch helps align. Mine slipped in easy

First point of leakage was the door. Turns out that a gasket at the bottom of the door functions as a wave trap. As the bottom sprayer spins it sprays against the door and creates a small wave of water this gasket was starting to disintegrate, it was letting water surge over the small tray at the doors bottom. Easy to replace just pull down and remove press fit on inside door bottom. Only when this was replaced did I find the real leak but not until I guessed at the tub seal as the leak. Very hard to see where the water really comes from! Turns out it was not the tub seal but a clip that holds the heater element got smashed down from a dropped dish rack at some earlier time and this caused the heat to increase at the clip and eventually heat the clip to extent it melted the tub directly under it. JB Weld to the rescue and we have a waterproof tub again. Well almost! The tub gasket resisted my best efforts to seat correctly and thus required a new tub gasket, still hard to seat but after 2-3 attempts we have a winner. Total cost about 50 bucks vs. 6-700 for a new unit. Wife is happy!!

Turned off elecrtic and water to dishwasher and pulled dishwasher out from under cabinet. Removed broken hose using pliers to open hose clamps.
installed new hose.

It only took about 20 minutes to replace. Thanks for the video.

Removed damaged strike plate from dishwasher and screwed new part into place. Tested and dishwasher worked fine. Took less than 15 minutes to get the job done. Was very pleased with how fast the part was delivered.

Removed the bottom panel, and I had to disconnect the water supply, which did NOT use flexible tubing (much to my disappointment), removed the screws holding the diswasher in the cabinet. Slid it out, took the old springs off, put the new ones on.

It was pretty straightforward -- no big deal.