CDU610N Crosley Dishwasher - Instructions

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.

Both racks are just roll out & roll new racks back in, no tools. Racks came in just 2 days, one was damaged in transit. Called to advise PartSelect of the problem. replacement rack was here within 2 days.
Great service. Jack

Ordered new part from your site. The new basket arrived in just a few days, without the handle and cover for the small item section. Instructions with with new basket described how to remove the other parts from the old basket and install them on the new one. Everything worked out perfectly and my silverware stays put. I've very happy!!

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.

Thanks to all the previous posters for their hints.

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.

New pump housing filter was needed as the old one was plugged and distorted.

I

I had to take the complete builtin dishwasher out of the base cabinet in the kitchen.

turn off electricity - circuit box
turn of water supply - turncock under sink
remove kickplate - screw driver
disconnect electric wires - screw driver
disconnect water feed - 5/8 wrench
remove top screws at counter underside - screw driver
pull out dishwasher - hands and son
turn dishwasher upside down - hands and son
got some water on floor - towel to mop up
remove top shower hose ( a rigid pipe with a screw fitting at top and a neoprene coupler at bottom) - hands
The neoprene coupler is the part that failed, it had worn thin due to heavy water flow

reverse process - same tools

voila - no water leak

I replaced a Silverware basket at the same time, which took two mintues as I had to remove the handle from the old basket and press fit onto new one - hands

Parts Select had the parts I needed and delivered in less than 48 hours. That is great service.

The dishwasher was running perfectly, but over time it leaked more and more. We were ready to throw it out, when I searched the internet and saw stories about a tiny gasket commonly failing. I couldn't believe that could be the trouble, but ordered the $3.75 part. Unscrewed the door, slipped out the old gasket and slipped on the new one. Screwed the door back. And the result? THE LEAK IS FIXED! Unbelievable. The old gasket had gotten stiff, probably exposure to soap, and it wasn't sealing properly. That $3.75 part saved us hundreds and hundreds of dollars and will give us extra years of use from our dishwasher.

Just undid the brackets holding the top rack in place and put in the new racks, locked the brackets and in the bottom put the water tower on and slid that rack in place, and bam we were ready to turn it on. It's wonderful, all new and clean. LOVE IT!!!

I removed the bottom rack by simply rolling it out of the dishwasher, and removed (unsnapped) the rotating spray assembly. It was easily snapped into the center of the new dishrack. Next, I removed the roller stops from the rail holding the upper dishrack by following the marks (arrows) on the stops. I rolled out the upper dishrack, and rolled in the new one. Finally, I snapped the roller stops back into position.

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further