CDC400B Crosley Dishwasher - Instructions

I first changed the dispenser door latch grommet, which was very eazy except for the left side nut screw which was a little awkwaed to get to with the nut driver. Not a big problem but difficult enough that i stripped the threads (plastic) and had to get a larger screw which is working fine so far. Since the grommet didn't stop the leaking although it was obvious it was leaking from the soap trail. I ordered the gasket and got it very promptly put it on and guess what. Still leaked some. I discovered when they installed the dishwasher the door appeared to be warped. To fix this there are two door tension springs under the bottom panel. By adjusting these with a log screw driver problem finally solved.
It is good to have not only a great place to get parts but the idea's from others are terrific. Although this washer is 15 years old it looks new and now acts new. Thanks so much for good service and advise.

Lifted out the old rack and set in the new one. The raised portion of the new rack was not high enough to clear the lower spray tower, so I adjusted the back wheel "axles" downward about 3/8" with pliers, which raised the rear of the rack enough to clear the tower.

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

Even though there was plenty of water pressure from the pump, the lower arm would not spin. I could move it with my hand but there was too much friction for it to spin. Turns out an item named seal ring[38] (I would call it a slip ring) had become dislodged somehow at the interface between the rotating parts and the stationary parts but I did not learn that until I was able to disassemble it. I could see from the diagram that there were threads at the top of the SPRAY ARM SUPPORT[39] that engaged with the threads in the CENTER SPRAY NOZZLE EXTENSION[33] so I held the arm and tried to unscrew [33]. CRACK! The 4 thin plastic arms in [39] snapped right off. I then disassembled and found the dislodged seal ring[38]. I concluded that I would never have been able to disassemble without breaking [39] due to the calcium in the threads (even with repeated applications of vinegar or lime away): the plastic arms are just too wimpy. But the price of a new [39] was a bargain, I was amazed. Came in 2 days, I re-assembled, now the spray arm spins freely and the dishwasher works again. I will try to remember to use vinegar periodically incase the slip ring dislodges again. This has been a great dishwasher otherwise IMHO( and a bargain price).

Removed the old gasket, without tools, and fit the new gasket into the space, making sure it was in the groove correctly all around, job done, works great. The ordering of the gasket on this site was easy and the shipping time was amazing, one day. Would use this company again, and recommend to anyone needing parts that wants to do repairs themself. I am sure saved a whole lot over hiring someone, and got the job done sooner also.

Took off bottom plate for access. Slid part that holds bottom of spring forward so I could reach it without pulling dishwasher out of position. Hooked spring to bottom attachment, then connected door spring linkage to holder that is attached to the dishwasher frame. Adjusted the tension with the tension screw and buttoned up bottom plate.

After replacing the door gasket and seeing that this wasn't the problem, using the schematics found at partselect.com I finally realized that it may be the insulation foam strip. I ordered the product and received it very quickly. Installation went fairly quickly. It was easy to remove the old foam strip and install the new one. The only problem was that the foam strip was about 1/4 " too short and it didn't cover the entire bottom. I improvised a little bit and cut off some of the old strip and covered the gap. So far the leak seems to have been fixed. In addition to the foam strip I had to buy a torx screwdriver for $11 at the local hardware store. The total spent was around $25.

After examining the door and main seal around the dishwasher I thought everything looked okay. I looked online to order a new seal anyway and discovered from others that the leak was probably the insulation strip inside the door rather than the seal around the dishwasher. I ordered an insulation strip and it arrived a couple days later. I removed the seven screws of the interior door cover and disconnected the electrical. After removing the old insulation strip and installig the new one I reconnected the electrical wiring/plugs, put the door cover back on, and reinstalled the screws. Total time was about 15-20 minutes and the leak stopped. It was very easy and saved the cost of a repairman or a new dishwasher. I'm very glad that I "listened" to others and went with the new insulation strip.

1- turn power off. 2- remove 7 screws to take door apart 3- remove 2 screws to take dispenser out. 4- i unhooked electic plug from it. 5- replace grommet and all back together. not bad to be 72 years old.

I had to replace the faucet in the kitchen sink orignnally. However since I use a porteable dishwasher, its hose connects to the kitchen faucet. The new faucets aerator is threaded differently than the old so that the dishwasher adapter would not screw in. I had misplaced the adappter kit that came with the dishwasher last year, so I ordered the adapter from partselect.com. when the part came a few day it was a simple as screw out the old aerator, screwing in the new adapted and then putting the modified aerator from the old faucet back in so that the dishwasher can be connected as needed.

after reading the remarks from other DIY users of the site, I realized that not only did I need to replace the spray arm, but should replace the spray arm nut as well. The repair took less than a minute to unscrew the old one and add the new, and it has worked like a charm ever since. Thanks guys, and goooood luck.

My original order was for the "Motor Gasket" in the bottom of the tub that just looked nasty. Not leaking. Replacing that was a little more complicated, but used another customer's recommendations and worked great. Ran an empty load to check for leaks and thats when we discovered that we had a leak on the side of the darn thing. So we ordered the "Injector Seal Ring. Got it in about 5 days and after installing, (2 seconds), we still had a leak! Soooo, ordered the "Water Inlet Injector". 5 days later, we have NO MORE LEAKS!!! I would STRONGLY suggest that anyone who has a leak at the Water Inlet, order a new Injector right along with the Seal Ring. The shipping and handling was WAY more than the price of the parts. I'm happy to say that my 10 year old dishwasher is running like a champ. Thank You.

Take the bottom skirts off of front. Put drain solinoid back in its bore and secure with wire or a rubber band.It will be a chrome cylinder hanging Take the center spray section out and look for the broken lever. Get both pieces out if it split and fell in two. Mine usually crack and stay on the shaft. Pull the circlip off and slide new lever in place and replace circlip. Re-assemble center section. If you are going to keep the dishwasher buy extra levers. I buy them 2 at a time and try to keep a spare.

Our dishwasher got to the point where it would not complete a wash cycle. I found that by jiggling the door latch, the dishwasher would whir back to life. For awhile, if I put a clothespin on the door latch, somehow enough pressure would be put on the switch to keep the dishwasher going. Finally, the dishwasher refused to cooperate...so I ordered a replacement switch.

The repair was easy. I only had to remove the interior door panel, unscrew the metal bar at the top of the door and underneath the door panel, then remove the black plastic shield. After that, it was just a matter of wiggling the old switch out and wiggling the new switch.

CAUTION: Be very sure that the power to the dishwasher is turned off. I got a scare because I thought the circuit breaker was off, but I had flipped the wrong one and suddenly, with my fingers very close to the bare connectors, the dishwasher came back to life briefly. I ran downstairs and found the correct circuit breaker and all was fine after that.

Simply remove the washer nut,then pull the float assembly. As far the lever,just unscrew the screw and replace the actuator lever. What was great about everything I was able to go to the presented diagram. This allowed me to find the exact parts I needed. Of course make sure you have the model number.