CDU450V Crosley Dishwasher - Instructions

I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.

no problems, very easy

First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

The dishwasher was running perfectly, but over time it leaked more and more. We were ready to throw it out, when I searched the internet and saw stories about a tiny gasket commonly failing. I couldn't believe that could be the trouble, but ordered the $3.75 part. Unscrewed the door, slipped out the old gasket and slipped on the new one. Screwed the door back. And the result? THE LEAK IS FIXED! Unbelievable. The old gasket had gotten stiff, probably exposure to soap, and it wasn't sealing properly. That $3.75 part saved us hundreds and hundreds of dollars and will give us extra years of use from our dishwasher.

removed lower dish basket. then removed 3 screws lifted element cover and removed center hold down nut lifted spray nozzle nad installed new parts. dishwasher is working like new.
thanks for asking.

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

Took the handle off the old basket and put it on the new one and it was done.

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

Popped off the plactic screen filter (3 screws). Droped in the new Spary Arm and put back together.

You guys are AWESOME! I ordered the part on a Wednesday afternoon and received it Thursday morning. So all and all I didn't even have to wash any dishes by hand.

romoved 3 screws, removed spray arm support nut. pulled off spray arm support, replaced new spray arm support and spray arm support nut

first i unhooked the 2 hoses then removed the 2 screws holding the valve in place, I then removed the hose fitting from the old unit and installed it on the new one. I then bolted on the new valve and reconnected the hoses and it worked fine.

Pulled out the old gasket and pressed in the new one. No more leakage.

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.