DCR-211-1H-OM Caloric Dishwasher - Instructions

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

Replaced the faucet adapter, works fine

Laid over portable dishwasher and looked for evidence of a leak.Nothing obvious. Looked up Illustrated parts breakdown to see what could be the possible source and settled on the main seal on the water pump between the washing machine itself and the motor. Also replaced grommets on the heating element.She hasn't used it yet but am confident problem is solved.

I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!

Used a deep 13 mm socket to remove the old nuts, one of which was split which is what caused the problem. I installed the new grommets with the aid of a little olive oil and then I had to wiggle the element very slightly (more olive oil on the heating element where it slips in the grommet) while pressing down on the element. It slipped into place and then I reinstalled the new nuts and the wires and it was done. One word of caution the stainless mounts that hold the heating element are very sharp on the edges. If you use gloves and move them very easy to prevent damage to the mounts it will be easy to replace the grommets and the nuts.

There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.

I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!

I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!

Removed front toe kick plate, removed elect.wire, Lifted heating element up replaced old gromet seal put element back through tub put new not on the element and tighetend up with One half inch deep socket ,Replaced plastic wire cover over element spade conector replaced electric wire on to element. Start machine checked r leak, replace toe kick plate.......... Done

I unsrew the faucet head, and attached th e adapter