SHE55M12UC Bosch Dishwasher - Instructions

Slip the wheel onto the axle, snap the clip facing up onto the frame

Vice grip door hinges. No need to disconnect, un hook hing springs. Works slick. Small vice grips. On hinges. Remove tore screws. Remove seal , and replace seal, reconnect door screws. Boom done.

Ordered the complete soap /rinse additive unit.nturn power off. Take the peripherical screws to remove the front of the door. Slide the door down and off. Unplug wires 2 places. Use a screwdrive to pry the tabs allowing the unit to come out

Important. Add a little Vaseline to the seal on the new part. Press it in until the tabs engage. Reconnect wiring and replace door front. Turn power on Job complete.

just placed the basket in the rack

Replaced parts

Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.

Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.

Dishwasher racks are maddening. It takes years to understand how to make your dishes fit within your dishwasher. We just moved and nothing was working so I did something that I did not want to do--pay attention to the lower rack and figure out why it had a mind of its own. Well, the Bosch interior is filled with adjustable (that usually means problems) fingers. Well, it was not so. A piece was missing that supported the "hand" from which the fingers sprang. That support piece cost about a buck and was available and ultimately on my doorstep in a day or three. Take the part out of the bag, snap it on the hand and enjoy dish racks that don't flop around. Awesome indeed.

Remove lower panel
TURN OFF POWER AT BREAKER
Remove water line
Remove the screws on bottom left of washer to remove solenoid valve
Pull out solenoid valve carefully there is a wire plugged into it, far enough to remove clamp on the hose
Remove valve far enough to disconnect wire
Order correct valve assembly
Reinstall in reverse order

To replace the part per se was simple. To put everything back in place was more difficult as I took the base of the dishwasher off and a lor of other parts in order to reach for the drain pump. The irony was, after I took appart the base I fount a clip on the internet showing how to do that job and that was a very simple thing, couple of screws to take off the toe plate and the interior liner of the door, to create good access to the drain pump. Really a job of 10 minutes at the max.

My husband spent minimal time and maybe just screwdriver for repair of replacement part.
Your company was great to work with.
Thank you!

Removed old panel with about six screws. Removed all the buttons and reinstalled on new facia panel. Installed back on holder with two screws and reinstalled assembly. I was led to believe this replacement panel was made from stainless steel but it actually was the same plastic panel with a stainless finish. Same as the original. Pretty poor design to have the heavily used plastic handle held on with only two screws. I had epoxied it twice, but gave up and bought a new facia.

The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels (Part 10016657) for $42. They have been installed and the problem seems to have been fixed.

replaced left upright unfortunately I ordered 2 left and now I still need the right Wish they would have caught that on the order

Small child messed with keyboard during order process. Wrong part was ordered by mistake. Cancelled online order immediately as instructed online at Part Select. Those idiots still sent the wrong part anyway and I had to return repair part at my expense. These people don't bother to follow their on rules. Never would I order a repair part from these people again. I would rather just buy a new machine than use Part Select.