SGX68U55UC Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- spencer from gilbertsville, PA
- Parts Used:
- 12012913
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Handle on Bosch dishwasher had cracked
1) Remove the three torx screws securing the handle.
2) Open door. Placing some cushions under the door makes the operation easier.
3) Remove the 12 torx screws securing the door skin. Note the screws are of two sizes. The lower 6 are shorter and fatter than the upper 6, that also secure the control panel.
4) It’s useful to have a 2nd person or a counterweight to secure the door once the skin is removed.
5) Remove the old handle by snapping the securing tabs.
6) New handle is press to fit.
7) Return skin to door and re-insert screws to secure.
8) Re-insert the three handle screws.
Notes
1) A three red wire cable plug was floating in the breeze when i removed the skin. I assumed it had pulled loose during removal of the skin so inserted back into the control panel but the washer would not power up with it inserted. On removal it worked fine. Not sure it it serves a model specific function.
2) It may be possible to use a car trim pry tool to remove the handle but I was concerned the stainless might be distorted.
2) Open door. Placing some cushions under the door makes the operation easier.
3) Remove the 12 torx screws securing the door skin. Note the screws are of two sizes. The lower 6 are shorter and fatter than the upper 6, that also secure the control panel.
4) It’s useful to have a 2nd person or a counterweight to secure the door once the skin is removed.
5) Remove the old handle by snapping the securing tabs.
6) New handle is press to fit.
7) Return skin to door and re-insert screws to secure.
8) Re-insert the three handle screws.
Notes
1) A three red wire cable plug was floating in the breeze when i removed the skin. I assumed it had pulled loose during removal of the skin so inserted back into the control panel but the washer would not power up with it inserted. On removal it worked fine. Not sure it it serves a model specific function.
2) It may be possible to use a car trim pry tool to remove the handle but I was concerned the stainless might be distorted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from dumfries, VA
- Parts Used:
- 00628998
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Lip on handle cap snagged on clothing, cracked the lip and the body of the part
Removed the 12 torx-headed sheet metal screws holding tub-side of the door together.
Opened the door assembly, the wiring harness for the control panel prevents the separation of the door interior and exterior, which is necessary to access the door handle mounting hardware.
Lifted the control panel assembly up, which allowed separation of the door components to access the door handle hardware.
Removed and replaced the broken mount.
When reassembling the door, be careful to align the control panel and snap it back into the groove on the external door assembly be fore reinstalling the screws. Line up the screws carefully to allow flush mounting and avoid stripping the interior screw holes.
Opened the door assembly, the wiring harness for the control panel prevents the separation of the door interior and exterior, which is necessary to access the door handle mounting hardware.
Lifted the control panel assembly up, which allowed separation of the door components to access the door handle hardware.
Removed and replaced the broken mount.
When reassembling the door, be careful to align the control panel and snap it back into the groove on the external door assembly be fore reinstalling the screws. Line up the screws carefully to allow flush mounting and avoid stripping the interior screw holes.
Was this instruction helpful to you?
Thank you for voting!