SHU9955UC (12) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lawrence from FREDERICKSBRG, PA
- Parts Used:
- 00499500
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Overfill then no fill
Remove bottom kick plate and raise the feet up. Remove attachment from the top to counter. Slide out. Facing the unit, remove left hand side sheet metal cover. The unit is behind this cover. Unhook the hose on the lower end. Pop the new one in and hook it up!! Test on quick rinse and see results. If ok return to normal as disassembled. Make sure to level the unit after tucking it back in. Enjoy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from Hermon, NY
- Parts Used:
- 00642239
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Getting to the part at the bottom of the dishwasher was a little pain.
Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danette from SANTA FE, NM
- Parts Used:
- 00165314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing/broken wheel on right side of lower dishwasher rack
I snapped the part in and voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEBSTER, TX
- Parts Used:
- 00165253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replace catch for door latch
Dishwasher door won’t stay closed. Upon inspection, the metal striker/catch at the top of the door was broken. This dishwasher is 12 years old and this is the first problem I’ve had with it. To repair the catch, first remove screws holding cover plate at the bottom of the door. Next, remove screws holding the dishwasher stable from under the counter. The pull out the dishwasher to gain access to the catch. You’ll have to take a small set of pliers and bend the two tabs back that hold the catch in place. Lift the catch up and forward to remove. Replace and bend the tabs back to hold the new catch securely. Move the dishwasher back in place and secure with the screws previously removed. Put the cover plate back in place and you’re done.
Was this instruction helpful to you?
Thank you for voting!
Not pumping out
Remove spray arm. Pullout. Micro filter big screen . Tork bolt cover and small pliers to grab check valve flapper.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENN VALLEY, PA
- Parts Used:
- 00615079
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Clogged, old filter- dirty dishes
Removed old filter and replaced with new filter. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from NEW PARIS, IN
- Parts Used:
- 00166623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid for the streak treatment wouldn't stay shut.
Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ranaye from BECKER, MN
- Parts Used:
- 00165256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Not getting water
shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy from McArthur, CA
- Parts Used:
- 00239144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Watch the video
Parts perfect works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Redding, CT
- Parts Used:
- 00490467
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Needed to replace dispenser
The video pretty much showed it all except...if you have a custom panel on the front like ours did. In that case, yiu have to remove the torx screws along the top PLUS to extras in the side of the part that protrudes into the tub of the washer. Those two are key to releasing the front panel and are also held in with fairly flimsy spring steel so be careful. Otherwise, pretty easy to do.
Was this instruction helpful to you?
Thank you for voting!