SHX7PT55UC (01) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from Seattle, WA
- Parts Used:
- 12054183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leakage from the dishwasher; unknown source.
Followed the video on your site and it was an easy install with no more leakage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sequim, WA
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm plug into water source became worn out and difficult to engage
The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from MORROW, OH
- Parts Used:
- 12004119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The Cable Broke on both sides
The instructions stated to remove the door. I spent an hour attempting to remove the door. That was an unnecessary instruction. all else worked as described. Springs were easy to install. The attachment to the door was difficult. Better instructions on how to grasp the connection to spread the spring to give the cable enough slack to attach the connection to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Callan from CHICAGO, IL
- Parts Used:
- 12054183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Chronic water leakage
Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.
Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.
Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni from GREENSBORO, NC
- Parts Used:
- 00611475
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One Dishwasher bottom rack wheel broke
Popped the new one right on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from BAY VILLAGE, OH
- Parts Used:
- 00745001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The top door gasket on dishwasher cabinet was torn
Part arrived on time. Double checked it was the part I needed. I unclipped the old seal and snapped the new piece in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Bradenton, FL
- Parts Used:
- 00747056
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The insulating part had deteriorated and split, probably due to age
I simply removed the toe kick plate held on with two screws. The kick plate basically held the insulating part in place. The simple design made it easy to put it in place, return the kick plate and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from LA CROSSE, WI
- Parts Used:
- 20007189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower dish rack was rusting.
Replaced lower dish rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ashland, OR
- Parts Used:
- 00645208
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Disenser would not hold Finish solution - replaced unit
First - I watched 2 or 3 videos on how it was done. The operation was not as easy as the videos made it out to be. Removal of the old unit was straight forward using 6 coins as shims to spread open the metal clips that hold the unit in place was essential. One issue not covered well in the videos is supporting the control panel after it was removed. the wires hang and are supporting the panel which is not good. I used a bunch of masking tape to secure the control panel to the top of the door. Also - installing the new unit can really only be done by first, fully engaging the top of the dispenser and then forcibly "pushing" (I used a rubber mallet) the bottom into place. you need to make sure the clips are locked in on all sides. After the dispenser is in place and the wiring harness has been reattached, you need to tape the wiring onto the door to keep them out of the way. I then very loosely reattached the control unit by the top 2 screws. I then lowered to the door flat and weighted it down. I used a clamp on each side of the door to lift the cover up into place unit until it could screwed. and then jimmied the control panel into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from dumfries, VA
- Parts Used:
- 00628998
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Lip on handle cap snagged on clothing, cracked the lip and the body of the part
Removed the 12 torx-headed sheet metal screws holding tub-side of the door together.
Opened the door assembly, the wiring harness for the control panel prevents the separation of the door interior and exterior, which is necessary to access the door handle mounting hardware.
Lifted the control panel assembly up, which allowed separation of the door components to access the door handle hardware.
Removed and replaced the broken mount.
When reassembling the door, be careful to align the control panel and snap it back into the groove on the external door assembly be fore reinstalling the screws. Line up the screws carefully to allow flush mounting and avoid stripping the interior screw holes.
Opened the door assembly, the wiring harness for the control panel prevents the separation of the door interior and exterior, which is necessary to access the door handle mounting hardware.
Lifted the control panel assembly up, which allowed separation of the door components to access the door handle hardware.
Removed and replaced the broken mount.
When reassembling the door, be careful to align the control panel and snap it back into the groove on the external door assembly be fore reinstalling the screws. Line up the screws carefully to allow flush mounting and avoid stripping the interior screw holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MOORPARK, CA
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top arm water connection to rear wall - all seals eroded and leaking
Removed the middle basket and turned it upside down. Unplugged the spray arm from the middle basket. Snapped the new spray arm into the middle basket.
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too
Was this instruction helpful to you?
Thank you for voting!