SHX53T55UC (07) Bosch Dishwasher - Instructions

Fairly easy repair, with the hardest part getting the appliance out of the cabinet. Kill the power and get the dishwasher out. Once out, the water inlet assembly (a large, white, opaque plastic box) is on the left side of the dishwasher, exposed and surrounded by the sound insulation. Pull back the insulation and use pliers to disconnect the small, white water inlet tube (hard to remove, you may need to pry a bit with a flathead screwdriver). Once that's off, look on the back left of the dishwasher for the valve access, which is mounted on a plastic snap-in tab. It was easiest to snap this out by reaching into the dishwasher from the side and squeezing the tab on the assembly with my fingers. Once it's out, remove the electrical connection from the old valve access by squeezing the tab. Unscrew the incoming water hose (from water service), and squeeze the clamp to remove the smaller white hose. Then go in reverse to reassemble: connect the white hose to the valve access and clamp. Connect the water service (make sure the threads take and it's solidly hand-tightened). Connect the small electrical plug. Snap the panel back into the back of the dishwasher. Connect the small white hose back to the water inlet assembly on the left side of the dishwasher and clamp. Test if you can, then put insulation and appliance back in. This totally eliminated my E17 errors.

We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.

popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!

Replacement was fast and very simple. Was completed in less than 5 minutes.

easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet

There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.

removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.

Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!

The new rack arrived nearly ready to install. The brackets and wheels that connect the rack to the track in the dishwasher were already on the new rack when it was delivered. All I had to do was move some plastic parts from the old rack to the new rack. This is very easy and does not require any tools since the parts snap onto the racks. It's worth taking a moment to study the way each part is attached to the old rack before moving it to the new rack. Pay particular attention to exactly how & where the spray arm tube snaps to the rack. That tube took me two tries to get right. The whole operation took less than 15 minutes.

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

The repair was extremely simple. Just lined up and popped them on. No tools needed.

Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!

I ordered the wrong part....needed their help to locate the correct part.
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service

Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes

Note: The diagram and part description misled me to think that each item was a quantity of one, so I ordered two since I wanted to replace the part on each side of the door. In fact, both the cable repair kit and the guide came with a quantity of two, so have an extra set that I will likely never need. As far as the replacement, it was quick and easy. The hardest part was pulling the dishwasher out from under the cabinet.