SHP65TL5UC (02) Bosch Dishwasher - Instructions

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

Replacement was fast and very simple. Was completed in less than 5 minutes.

popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!

easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet

have had same problem many times under extended warranty pump was changed by factory and installed wrong it was jammed in so take out there is a realest lever and twist clockwise install buy twisting counter clockwize

removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.

There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.

The new rack arrived nearly ready to install. The brackets and wheels that connect the rack to the track in the dishwasher were already on the new rack when it was delivered. All I had to do was move some plastic parts from the old rack to the new rack. This is very easy and does not require any tools since the parts snap onto the racks. It's worth taking a moment to study the way each part is attached to the old rack before moving it to the new rack. Pay particular attention to exactly how & where the spray arm tube snaps to the rack. That tube took me two tries to get right. The whole operation took less than 15 minutes.

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!

The repair was extremely simple. Just lined up and popped them on. No tools needed.

To remove the old cutlery drawer I had to pull the old drawer forward and work the rollers over the stops at the end of the permanently installed slides. To install the new cutlery drawer, I reversed the procedure and worked the rollers on the new drawer over the slide stops and seat the new basket. No tools were required.

As for the crockery baskets, the larger lower basket was very simple. Roll it forward onto the door and lift it out. To install the new basket reverse the procedure. Place the new basket on the door and slide it in on its rollers.

For the upper crockery basket the procedure is more complex. The retaining mechanisms for the upper basket appear to be very complet as they have a number of moving parts intricately engineered. With a little study, it become apparent releasing the locks and levers which keep the basket from rolling out and falling to the floor are well designed to both secure the basket and to remove. Each anchoring mechanism has a lever at the base and by depressing the lever it releases the basket so it can be rolled forward over the stops at the end of the slides. Some manual dexterity is required to maintain pressure on the mechanisms to ensure the basket will be released. The procedure is quickly mastered with a few attempts. The good thing is again no tools are required.

My new tray and baskets are working fine and it is a relief to have the old rusting and deteriorating tray and basket replaced. This is true for both safeguarding the crockery and cutlery form rust and chemical of deteriorating plastics, rusting metal, and bonding agents. More important, I am sure replacing the old deteriorating baskets and tray guards against any potential health issues.

I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.

Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes

Note: The diagram and part description misled me to think that each item was a quantity of one, so I ordered two since I wanted to replace the part on each side of the door. In fact, both the cable repair kit and the guide came with a quantity of two, so have an extra set that I will likely never need. As far as the replacement, it was quick and easy. The hardest part was pulling the dishwasher out from under the cabinet.