SHP65T52UC (02) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bryan from SUWANEE, GA
- Parts Used:
- 10023852
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
E15 Error Code
Turned off power and water supply. Pulled dishwasher out. Disconnected the water inlet from the back left side. Swapped out the inlet valve. Wiped up the water in the bottom pan. Put dishwasher back and turned on water and power. Simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from CLERMONT, FL
- Parts Used:
- 12054183
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water leak on top of door.
Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEXINGTON, KY
- Parts Used:
- 00645038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filter-Micro was clogged with lime from hard water.
Replacement was fast and very simple. Was completed in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from MADISON, CT
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher door would not close properly, spray arm would not engage plug
popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!
couldn't be any easier, 5 minute job, door closes easily now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from STURGEON BAY, WI
- Parts Used:
- 00611475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
There was a roller missing from the lower washing rack.
There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BAYTOWN, TX
- Parts Used:
- 00611475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels on the bottom tray broke off
The repair was extremely simple. Just lined up and popped them on. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from EDINA, MN
- Parts Used:
- 00645038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Over the years the filter became too clogged with embedded particles
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Wichita, KS
- Parts Used:
- 11026683
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
The old basket didn’t fit in the new lower rack
just placed the basket in the rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WASHINGTON, MI
- Parts Used:
- 10023852
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.
Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from LA CROSSE, WI
- Parts Used:
- 20007189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower dish rack was rusting.
Replaced lower dish rack
Was this instruction helpful to you?
Thank you for voting!
The metal support frame for my old cutlery basket was rusted which required replacement.
To remove the old cutlery drawer I had to pull the old drawer forward and work the rollers over the stops at the end of the permanently installed slides. To install the new cutlery drawer, I reversed the procedure and worked the rollers on the new drawer over the slide stops and seat the new basket. No tools were required.
As for the crockery baskets, the larger lower basket was very simple. Roll it forward onto the door and lift it out. To install the new basket reverse the procedure. Place the new basket on the door and slide it in on its rollers.
For the upper crockery basket the procedure is more complex. The retaining mechanisms for the upper basket appear to be very complet as they have a number of moving parts intricately engineered. With a little study, it become apparent releasing the locks and levers which keep the basket from rolling out and falling to the floor are well designed to both secure the basket and to remove. Each anchoring mechanism has a lever at the base and by depressing the lever it releases the basket so it can be rolled forward over the stops at the end of the slides. Some manual dexterity is required to maintain pressure on the mechanisms to ensure the basket will be released. The procedure is quickly mastered with a few attempts. The good thing is again no tools are required.
My new tray and baskets are working fine and it is a relief to have the old rusting and deteriorating tray and basket replaced. This is true for both safeguarding the crockery and cutlery form rust and chemical of deteriorating plastics, rusting metal, and bonding agents. More important, I am sure replacing the old deteriorating baskets and tray guards against any potential health issues.
As for the crockery baskets, the larger lower basket was very simple. Roll it forward onto the door and lift it out. To install the new basket reverse the procedure. Place the new basket on the door and slide it in on its rollers.
For the upper crockery basket the procedure is more complex. The retaining mechanisms for the upper basket appear to be very complet as they have a number of moving parts intricately engineered. With a little study, it become apparent releasing the locks and levers which keep the basket from rolling out and falling to the floor are well designed to both secure the basket and to remove. Each anchoring mechanism has a lever at the base and by depressing the lever it releases the basket so it can be rolled forward over the stops at the end of the slides. Some manual dexterity is required to maintain pressure on the mechanisms to ensure the basket will be released. The procedure is quickly mastered with a few attempts. The good thing is again no tools are required.
My new tray and baskets are working fine and it is a relief to have the old rusting and deteriorating tray and basket replaced. This is true for both safeguarding the crockery and cutlery form rust and chemical of deteriorating plastics, rusting metal, and bonding agents. More important, I am sure replacing the old deteriorating baskets and tray guards against any potential health issues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from PARSIPPANY, NJ
- Parts Used:
- 00611475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Four wheels on the lower dishwasher rack came off and got lost.
I bought replacement wheels.
I put them on the post, and they snapped onto the vertical post very easily. Job done.
I put them on the post, and they snapped onto the vertical post very easily. Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheldon from ROCKAWAY, NJ
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We accidentally damaged the upper spray arm
Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from LINCOLN, CA
- Parts Used:
- 12012912
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
plastic chrome trim on the door handle was broken.
Simply removed the four screws holding the handle in place, gently removed the handle and inserted the new part. You have to be careful and work slowly in order not to damage the front of the door while getting the snap locks unsnapped.
Once the old part was removed, simply snap in the new part and put the screws back.
Great help in locating the correct part on the phone.
Once the old part was removed, simply snap in the new part and put the screws back.
Great help in locating the correct part on the phone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orin from SPOKANE, WA
- Parts Used:
- 12012912
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Center section of handle broken
The handle fits from the inside of the outer door panel. I removed the panel. The handle is easier to remove if you break it in the middle. I then installed the handle and front panel. Note the length of the screws and their positions.
Was this instruction helpful to you?
Thank you for voting!