SHP53T55UC (07) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from WILDWOOD, MO
- Parts Used:
- 10023852
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Bosch Dishwasher repeatedly reporting error E17 after a few minutes of running
Fairly easy repair, with the hardest part getting the appliance out of the cabinet. Kill the power and get the dishwasher out. Once out, the water inlet assembly (a large, white, opaque plastic box) is on the left side of the dishwasher, exposed and surrounded by the sound insulation. Pull back the insulation and use pliers to disconnect the small, white water inlet tube (hard to remove, you may need to pry a bit with a flathead screwdriver). Once that's off, look on the back left of the dishwasher for the valve access, which is mounted on a plastic snap-in tab. It was easiest to snap this out by reaching into the dishwasher from the side and squeezing the tab on the assembly with my fingers. Once it's out, remove the electrical connection from the old valve access by squeezing the tab. Unscrew the incoming water hose (from water service), and squeeze the clamp to remove the smaller white hose. Then go in reverse to reassemble: connect the white hose to the valve access and clamp. Connect the water service (make sure the threads take and it's solidly hand-tightened). Connect the small electrical plug. Snap the panel back into the back of the dishwasher. Connect the small white hose back to the water inlet assembly on the left side of the dishwasher and clamp. Test if you can, then put insulation and appliance back in. This totally eliminated my E17 errors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from CLERMONT, FL
- Parts Used:
- 12054183
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water leak on top of door.
Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from ATASCADERO, CA
- Parts Used:
- 12014146
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Pet Rat chewed through wiring harness
It is important to remove the dishwasher to a workable space. Probably best to set it on a slightly higher platform, otherwise you're on the floor.
1. remove racks,
2. disconnect power supply and water line (turn off at source).
3. remove the exterior insulation.
4. One can now access the harness from both side of the washer.
5. Inspect and determine what connection goes where, all have color coded wire.Connections are notched
6. Recommend that each connection is removed and new connection replaced at that time
7.removing screws from the inside door to connect the harness to select connection.
7.button-up the door, replace insulation and reattach water line and power, reinstall machine.
8. You may have to remove the front toe-kick to access routing the wires.
1. remove racks,
2. disconnect power supply and water line (turn off at source).
3. remove the exterior insulation.
4. One can now access the harness from both side of the washer.
5. Inspect and determine what connection goes where, all have color coded wire.Connections are notched
6. Recommend that each connection is removed and new connection replaced at that time
7.removing screws from the inside door to connect the harness to select connection.
7.button-up the door, replace insulation and reattach water line and power, reinstall machine.
8. You may have to remove the front toe-kick to access routing the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEXINGTON, KY
- Parts Used:
- 00645038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filter-Micro was clogged with lime from hard water.
Replacement was fast and very simple. Was completed in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from MADISON, CT
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher door would not close properly, spray arm would not engage plug
popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!
couldn't be any easier, 5 minute job, door closes easily now!
Was this instruction helpful to you?
Thank you for voting!
The washer had an error message in the display of E:09. I called Bosh on customer srevice and she said that the heat pump was not working and needed to be replaced. Since the motor is the main part for this that needed to be replaced as well. The pars were under $200.00 total so we oted to fix this
We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from AUBURN, IN
- Parts Used:
- 00611320
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dishwasher not emptying tub, dirty dishes when the dishwasher said the cycle was done
easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from STURGEON BAY, WI
- Parts Used:
- 00611475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
There was a roller missing from the lower washing rack.
There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from CHESTER, WV
- Parts Used:
- 12008381
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Pump and heater failure!
Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!
Was this instruction helpful to you?
Thank you for voting!
WATER DRAIN MATRIX became plugged with sludge, stopping ventilation for draining function
removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WASHINGTON, MI
- Parts Used:
- 10023852
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.
Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from EDINA, MN
- Parts Used:
- 00645038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Over the years the filter became too clogged with embedded particles
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BAYTOWN, TX
- Parts Used:
- 00611475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels on the bottom tray broke off
The repair was extremely simple. Just lined up and popped them on. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from LANDENBERG, PA
- Parts Used:
- 11018097
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My flow tube had a hole in it
Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from SUN CITY WEST, AZ
- Parts Used:
- 10032849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Got the wrong part.......NEVER got an answer to my 3 emails to customer service to find the correct part
I ordered the wrong part....needed their help to locate the correct part.
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service
Was this instruction helpful to you?
Thank you for voting!