SHE65P05UC (63) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from Seattle, WA
- Parts Used:
- 00494772
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leakage from the dishwasher; unknown source.
Followed the video on your site and it was an easy install with no more leakage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Lake Stevens, WA
- Parts Used:
- 00642239
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Droning noise coming from the dishwasher
First of all, I quessed at what was causing the droning noise. It seemed that it started when the d.w. was draining. I looked at various sites to try and figure out what was causing the noise but they all wanted money up front before they would discuss the problem. I gambled that it was the drain pump figuring that, oh well at least it's a part I won't have to replace in the future. I got lucky, the noise stopped with the part I bought. The only issues were the wiring harnesss wasn't the same as in the video I used. Overall, your service was very good. The thing I'm disappointed with is the fact that my expensive Bosch d.w. had to be repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue E from CARMEL, IN
- Parts Used:
- 00166623
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Rinse aid dispenser lid would not stay closed
Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cori from OWATONNA, MN
- Parts Used:
- 00424673
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic On/Off Button Broke
1. Open the dishwasher door.
2. Unscrew the screws located along the insides and top inside of the door.
3. The lower front panel will release; remove and set it aside.
4. Unscrew the inside left and right side screws near the top control panel while supporting the control panel as it releases.
5. Unplug the plug from the junction box by the On/Off button. (Pinch clips to release.)
6. Slide the junction box up to release it from the door and set aside.
7. Unscrew the four interior screws on the control panel. The control panel plate can be opened slightly so that you can sneak the new button into place from the top. One end of the button has a bar; place that end into the brackets built into the interior of the control panel wall.
8. Carefully reclose the control panel ensuring that the brackets/hooks align and snap together.
9. Replace the four interior screws on the control panel.
10. Replace the On/Off junction box by pushing it up towards the button (engages the On/Off toggle) and then sliding it down to lock it into the brackets in the control panel.
11. Replug the plug into the junction box.
12. Reposition the door front and control panel in place on the door. (door front tucks under the control panel).
13. Refasten one screw on each door panel side and the two interior side screws for the control panel. This helps hold it all together while you can complete the remaining screws.
14. Refasten all remaining screws on the sides and top of the interior door.
15. Done!
2. Unscrew the screws located along the insides and top inside of the door.
3. The lower front panel will release; remove and set it aside.
4. Unscrew the inside left and right side screws near the top control panel while supporting the control panel as it releases.
5. Unplug the plug from the junction box by the On/Off button. (Pinch clips to release.)
6. Slide the junction box up to release it from the door and set aside.
7. Unscrew the four interior screws on the control panel. The control panel plate can be opened slightly so that you can sneak the new button into place from the top. One end of the button has a bar; place that end into the brackets built into the interior of the control panel wall.
8. Carefully reclose the control panel ensuring that the brackets/hooks align and snap together.
9. Replace the four interior screws on the control panel.
10. Replace the On/Off junction box by pushing it up towards the button (engages the On/Off toggle) and then sliding it down to lock it into the brackets in the control panel.
11. Replug the plug into the junction box.
12. Reposition the door front and control panel in place on the door. (door front tucks under the control panel).
13. Refasten one screw on each door panel side and the two interior side screws for the control panel. This helps hold it all together while you can complete the remaining screws.
14. Refasten all remaining screws on the sides and top of the interior door.
15. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C Loren from TWIN FALLS, ID
- Parts Used:
- 10002494
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
When I checked the drain filter to clean, I noticed the plastic supports were broken and the micro screen had collapsed.
I took out the old filter and replaced it with the filter I had ordered. Very easy and not necessary to call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from Hermon, NY
- Parts Used:
- 00642239
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Getting to the part at the bottom of the dishwasher was a little pain.
Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Melvin from TOWANDA, PA
- Parts Used:
- 00683965
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the fasica cracked
First turn off power source. Remove screws on each side of door, than remoe the door by pulling on the bottom once the door is off remove screws on inside top and the four scres that hole the facia in place these screws are under the door that you removed. then lift off the facia. remoe the push buttons and insert in the new part. be sure they are snap in place. than replace the facia be sure to align the part so it fits properly. install the screws to hold part in place then the screws on the top inside of door. once complete install the screwqs down each side of the door. turn power on. you should have completed the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ranaye from BECKER, MN
- Parts Used:
- 00165256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Not getting water
shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from NEW PARIS, IN
- Parts Used:
- 00166623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid for the streak treatment wouldn't stay shut.
Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from HUNTINGTN STA, NY
- Parts Used:
- 10002494
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Drain filter got old fell apart
Unscrewed the old piece screwed in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from TAMPA, FL
- Parts Used:
- 00649332
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
racks rusting
replaced left upright unfortunately I ordered 2 left and now I still need the right Wish they would have caught that on the order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from PERU, NY
- Parts Used:
- 00617087
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing wheel on the lower shelf of the dishwasher made it difficult to slide in and out.
The wheel easily snapped in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Redding, CT
- Parts Used:
- 00490467
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Needed to replace dispenser
The video pretty much showed it all except...if you have a custom panel on the front like ours did. In that case, yiu have to remove the torx screws along the top PLUS to extras in the side of the part that protrudes into the tub of the washer. Those two are key to releasing the front panel and are also held in with fairly flimsy spring steel so be careful. Otherwise, pretty easy to do.
Was this instruction helpful to you?
Thank you for voting!