SHP87PZ55N/18 Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peter from LEXINGTON, KY
- Parts Used:
- 00645038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filter-Micro was clogged with lime from hard water.
Replacement was fast and very simple. Was completed in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
WATER DRAIN MATRIX became plugged with sludge, stopping ventilation for draining function
removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from LANDENBERG, PA
- Parts Used:
- 11018097
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My flow tube had a hole in it
Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WASHINGTON, MI
- Parts Used:
- 10023852
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.
Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from EDINA, MN
- Parts Used:
- 00645038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Over the years the filter became too clogged with embedded particles
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CLYDE from TREGO, MT
- Parts Used:
- 10040888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
When loaded, the lower rack would fall off the rails
The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels (Part 10016657) for $42. They have been installed and the problem seems to have been fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheldon from ROCKAWAY, NJ
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We accidentally damaged the upper spray arm
Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sequim, WA
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm plug into water source became worn out and difficult to engage
The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- spencer from gilbertsville, PA
- Parts Used:
- 12012913
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Handle on Bosch dishwasher had cracked
1) Remove the three torx screws securing the handle.
2) Open door. Placing some cushions under the door makes the operation easier.
3) Remove the 12 torx screws securing the door skin. Note the screws are of two sizes. The lower 6 are shorter and fatter than the upper 6, that also secure the control panel.
4) It’s useful to have a 2nd person or a counterweight to secure the door once the skin is removed.
5) Remove the old handle by snapping the securing tabs.
6) New handle is press to fit.
7) Return skin to door and re-insert screws to secure.
8) Re-insert the three handle screws.
Notes
1) A three red wire cable plug was floating in the breeze when i removed the skin. I assumed it had pulled loose during removal of the skin so inserted back into the control panel but the washer would not power up with it inserted. On removal it worked fine. Not sure it it serves a model specific function.
2) It may be possible to use a car trim pry tool to remove the handle but I was concerned the stainless might be distorted.
2) Open door. Placing some cushions under the door makes the operation easier.
3) Remove the 12 torx screws securing the door skin. Note the screws are of two sizes. The lower 6 are shorter and fatter than the upper 6, that also secure the control panel.
4) It’s useful to have a 2nd person or a counterweight to secure the door once the skin is removed.
5) Remove the old handle by snapping the securing tabs.
6) New handle is press to fit.
7) Return skin to door and re-insert screws to secure.
8) Re-insert the three handle screws.
Notes
1) A three red wire cable plug was floating in the breeze when i removed the skin. I assumed it had pulled loose during removal of the skin so inserted back into the control panel but the washer would not power up with it inserted. On removal it worked fine. Not sure it it serves a model specific function.
2) It may be possible to use a car trim pry tool to remove the handle but I was concerned the stainless might be distorted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Bradenton, FL
- Parts Used:
- 00747056
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The insulating part had deteriorated and split, probably due to age
I simply removed the toe kick plate held on with two screws. The kick plate basically held the insulating part in place. The simple design made it easy to put it in place, return the kick plate and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MOORPARK, CA
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top arm water connection to rear wall - all seals eroded and leaking
Removed the middle basket and turned it upside down. Unplugged the spray arm from the middle basket. Snapped the new spray arm into the middle basket.
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from PERU, NY
- Parts Used:
- 10040888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing wheel on the lower shelf of the dishwasher made it difficult to slide in and out.
The wheel easily snapped in.
Was this instruction helpful to you?
Thank you for voting!