SHX87PZ55N/18 Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
WATER DRAIN MATRIX became plugged with sludge, stopping ventilation for draining function
removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from WASHINGTON, MI
- Parts Used:
- 10023852
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.
Repair was simple once the problem was diagnosed with the inlet valve.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from LANDENBERG, PA
- Parts Used:
- 11018097
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My flow tube had a hole in it
Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from EDINA, MN
- Parts Used:
- 00645038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Over the years the filter became too clogged with embedded particles
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheldon from ROCKAWAY, NJ
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We accidentally damaged the upper spray arm
Easily removed the old one by carefully pulling it and repeated this procedure to replace it. Total time took less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CLYDE from TREGO, MT
- Parts Used:
- 10040888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
When loaded, the lower rack would fall off the rails
The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels (Part 10016657) for $42. They have been installed and the problem seems to have been fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Wichita, KS
- Parts Used:
- 00675794
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
The old basket didn’t fit in the new lower rack
just placed the basket in the rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sequim, WA
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm plug into water source became worn out and difficult to engage
The spray arm makes a slide in attachment to a slide out drawer. It was removed by forcing out of the connection on the back of the drawer and the replacement was installed by sliding it into the same connection point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from LA CROSSE, WI
- Parts Used:
- 20007189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lower dish rack was rusting.
Replaced lower dish rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Bradenton, FL
- Parts Used:
- 00747056
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The insulating part had deteriorated and split, probably due to age
I simply removed the toe kick plate held on with two screws. The kick plate basically held the insulating part in place. The simple design made it easy to put it in place, return the kick plate and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from dumfries, VA
- Parts Used:
- 00628998
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Lip on handle cap snagged on clothing, cracked the lip and the body of the part
Removed the 12 torx-headed sheet metal screws holding tub-side of the door together.
Opened the door assembly, the wiring harness for the control panel prevents the separation of the door interior and exterior, which is necessary to access the door handle mounting hardware.
Lifted the control panel assembly up, which allowed separation of the door components to access the door handle hardware.
Removed and replaced the broken mount.
When reassembling the door, be careful to align the control panel and snap it back into the groove on the external door assembly be fore reinstalling the screws. Line up the screws carefully to allow flush mounting and avoid stripping the interior screw holes.
Opened the door assembly, the wiring harness for the control panel prevents the separation of the door interior and exterior, which is necessary to access the door handle mounting hardware.
Lifted the control panel assembly up, which allowed separation of the door components to access the door handle hardware.
Removed and replaced the broken mount.
When reassembling the door, be careful to align the control panel and snap it back into the groove on the external door assembly be fore reinstalling the screws. Line up the screws carefully to allow flush mounting and avoid stripping the interior screw holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MOORPARK, CA
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top arm water connection to rear wall - all seals eroded and leaking
Removed the middle basket and turned it upside down. Unplugged the spray arm from the middle basket. Snapped the new spray arm into the middle basket.
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too
Installed middle basket into slides.
It works great. Great site for parts - reasonable prices too
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from PERU, NY
- Parts Used:
- 10040888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing wheel on the lower shelf of the dishwasher made it difficult to slide in and out.
The wheel easily snapped in.
Was this instruction helpful to you?
Thank you for voting!