SHX89PW55N (01) Bosch Dishwasher - Instructions

The E:15 error code means water is detected in the pan under the unit. There are several ways this can happen.

In this case, it was caused by a bad inlet valve. It did not close properly and led to an overflow of water inside that eventually spilled into the pan underneath the unit.

I see now why the pump keeps running after this error. In this case, it would have led to a big flood in the kitchen if it did not.

I was actually able to run the unit while broke by manually operating the valve under our sink that provides water to the unit.

Be sure to turn off breaker before servicing. Don't get shocked!

Be sure to turn off water before starting! Or, you'll have a flood.

Anyway, I just pulled the unit out (was secured by 2 screws on the sides). I lifted up the insulation material on the left side to get at the valve. Pushed a little green tab to release the electrical plug. Then, use pliers to move clamp off the white water hose on the inside. Then, pull of white hose. This was hard in my case. Took a lot of force. Then, reach behind the unit and use pliers to unscrew water hose. Now, the whole gray panel there can pop out with some force. Then, slip the old valve out and slip new one in. Reconnect hoses and clamp. Note that I put some caulk on the connector where white hose goes. Not sure if needed or not.

Good luck!

Removed the spray arm, front handle, and little clips from the old rack and installed onto the new rack. Was very simple.

Turned off electric
Slid out unit - the water connection on this model is in the back
Disconnected the H2O hose. This valve access part is the part that connects the dishwasher to the H2O supply. The soon to be replaced part had sediment in it preventing H2O to go into the dishwasher and into the basin instead. The exploded view of dishwasher was a big help. It was a guess as to why this was happening. Now that I’ve had it apart it makes sense that this is the part that would fail after a period of time, especially if you have city H2O. My husband Bob did this repair.

Removed old rack and several accessory pieces, and installed them on the new rack. Slid the new rack back in. Took about 15-20 minutes top. Very easy to do.

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

I watch utube to assess the problem then took eveything apart and saw the build up on the filter, which i had never cleaned. I tried to clean it but was unsuccessful so order the filter from partselect and it came within a couple of days, installed very easily and began to clean as it always had.

Followed the video on your site and it was an easy install with no more leakage.

Replacement was fast and very simple. Was completed in less than 5 minutes.

Followed You Tube video how to replace door handle caps and used above mentioned tool. Note: could not use a regular screwdriver.

Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.

Fairly easy repair, with the hardest part getting the appliance out of the cabinet. Kill the power and get the dishwasher out. Once out, the water inlet assembly (a large, white, opaque plastic box) is on the left side of the dishwasher, exposed and surrounded by the sound insulation. Pull back the insulation and use pliers to disconnect the small, white water inlet tube (hard to remove, you may need to pry a bit with a flathead screwdriver). Once that's off, look on the back left of the dishwasher for the valve access, which is mounted on a plastic snap-in tab. It was easiest to snap this out by reaching into the dishwasher from the side and squeezing the tab on the assembly with my fingers. Once it's out, remove the electrical connection from the old valve access by squeezing the tab. Unscrew the incoming water hose (from water service), and squeeze the clamp to remove the smaller white hose. Then go in reverse to reassemble: connect the white hose to the valve access and clamp. Connect the water service (make sure the threads take and it's solidly hand-tightened). Connect the small electrical plug. Snap the panel back into the back of the dishwasher. Connect the small white hose back to the water inlet assembly on the left side of the dishwasher and clamp. Test if you can, then put insulation and appliance back in. This totally eliminated my E17 errors.

Hello,
I received the parts 12/10/23. Thank you for your prompt shipping. It was exactly what I needed and the fix went quickly with no issues.

I ordered two of PS8728568 (Mounting Bracket), because on your site for that part it identifies that each bracket is sold individually. (Reference: “Part Description” section). In addition, on that same web page under the “Question and Answers” section it identifies that each bracket is sold individually.

However, what I received was, two packages with each package having two brackets in it. It’s understandable, since you need two brackets for each dishwasher.

Obviously, this is completely contrary to what your web page states. In reality, each package is sold with a pair of brackets.

I have not opened the second package and as such it is completely resaleable. As per your Return Policy , I’d like to request a refund for the second packet of brackets and have you cover the return shipping of that package. Please advise next steps.

Turned off power and water supply. Pulled dishwasher out. Disconnected the water inlet from the back left side. Swapped out the inlet valve. Wiped up the water in the bottom pan. Put dishwasher back and turned on water and power. Simple.

The problem and solution were described on the internet. I ordered a set of 4 wheels for $43+. I received one wheel. When I called Drew told me that the order was correct, but the description on the web page was wrong. He was to sent me a return label, but it has not arrived. Since then I went to the Bosch website, found the set of wheels (Part 10016657) for $42. They have been installed and the problem seems to have been fixed.

popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!