SHE4402UC (22) Bosch Dishwasher - Instructions

Remove front door remove screw holding pump replace pump

Reading other posts I saw that the issue was not the button or the latch but the fact that stress is mostly applied to the two pieces of plastic holding fastening screws on the front. Both plastic pieces broke off the main fascia. Phone support got me the correct repair piece and youtube video showed the replacement very well. Hardest part was finding the Torx bit at Home Depot. Once replaced all seems to be working perfectly.

First of all, I quessed at what was causing the droning noise. It seemed that it started when the d.w. was draining. I looked at various sites to try and figure out what was causing the noise but they all wanted money up front before they would discuss the problem. I gambled that it was the drain pump figuring that, oh well at least it's a part I won't have to replace in the future. I got lucky, the noise stopped with the part I bought. The only issues were the wiring harnesss wasn't the same as in the video I used. Overall, your service was very good. The thing I'm disappointed with is the fact that my expensive Bosch d.w. had to be repaired.

Small child messed with keyboard during order process. Wrong part was ordered by mistake. Cancelled online order immediately as instructed online at Part Select. Those idiots still sent the wrong part anyway and I had to return repair part at my expense. These people don't bother to follow their on rules. Never would I order a repair part from these people again. I would rather just buy a new machine than use Part Select.

Disconnected the water and power, pulled dishwasher out from under the counter, unscrewed the old inlet valve, disconnected hose from exit of inlet valve, noted the placement of the wires and disconnected them. Installed new inlet valve in reverse order and reinstalled dishwasher.

Followed the video on your site and it was an easy install with no more leakage.

I have granite countertops and one of the hold down brackets broke to wood cabinet side mount. Easy and fast repair to remove old brackets, pull out dishwasher, and I replaced both brackets with new, and new wood screws. New installation looks better than original done 18 years ago. Very easy to do and saved a lot of money if I had an appliance repair company do it.

Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.

I snapped the part in and voila!

Replaced ‘sump’ housing , seal was leaking on it- replaced inop float on water level warning system switch, and switch itself as well- replaced drain pump motor attached to sump- replaced o-ring seal at water sprayer inlet valve- replaced water inlet plastic assemble on side of dishwasher- replaced drain hose out of sump assembly.

Used YouTube video to understand repair- this is an involved repair in time and complexity- dishwasher eventually gets turned upside down once removed and stripped down, to remove the white plastic water pan , which then allows access to the guts of all the above parts- some critical seals only come with new assemblies, so you are buying that new part to get a new seal and ensure no new leaks from what you took apart.

I removed the old electronic facia. You will need to remove the front bottom panel to get to the bottom screws that attach the facia. Be careful there are some sharp edges. After removing the bottom 2 screws you will need find 2 clips at the bottom sides of the facia. When the clips are free pull the bottom out first then lift up. You will need to transfer the buttons from the old unit. Lift those all the way up gently and they should come out easily. It would probably be a good idea to first number the buttons to ease them going back on. You don’t need to take this step as long as you notice the buttons on the right have different lengths in back due to the curvature of the facia. Reverse the process to reattach.

Removed old filter and replaced with new filter. Easy.

shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done

The perfect replacement part. Plug and play.

Remove spray arm. Pullout. Micro filter big screen . Tork bolt cover and small pliers to grab check valve flapper.