ADB1400PYB5 Amana Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Springhill, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from TRINIDAD, CO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
I can not get the part to fit and stay in place.
It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from GLADSTONE, MO
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from DEVINE, TX
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Element was no longer working. Dishes were not drying.
Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from MILWAUKEE, WI
- Parts Used:
- W10518394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not start & green "Clean" light was flashing
After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WEST SUFFIELD, CT
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
No directions with parts!
Could not take apart the upper rack on my whirlpool dishwasher to replace its wheels to transport its upper rack. The received parts did not match the old ones. Called parts and they suggested these new parts remanufactured and changed from the old ones but they had not been notified. Brought to professional mechanics and they figured it out. Bullshit parts company!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Hollywood, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water not heating,dishes not drying
My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Southbury, CT
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door is designed to stay in place when opened. Door should hold partial or fully open.
Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from Humble, TX
- Parts Used:
- WPW10477552, W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The green "Clean Light" was staying on after shutting down in the middle of the cycle. I put it in troubleshooting mode and found out it was the heating element.
Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MILLBURY, MA
- Parts Used:
- W11175771
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wasn’t getting water.
I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from SAN DIEGO, CA
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replacing
The old filter simply unscrews and the new one screws in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!