ADB1400PYB0 Amana Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Heating Element Burned Out
The repair was straightforward. The hardest parts were pulling the dishwasher out from the counter and keeping the dishwasher from falling forward when I needed to reach inside. The instructions in the video were accurate. I was very glad I bought the rubber washers, because I could not reuse the washers from the original heating element. Easy enough repair to do on your own.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was drying the dishes.
Followed directions from YouTube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond J from MOKELUMNE HL, CA
- Parts Used:
- WP8533380
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old cap came loose, fell onto heating element. End of story.
Bought the new cap, took it out of package, installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter O from CROYDON, PA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not empty.
Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from CLINTWOOD, VA
- Parts Used:
- W11175771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
clean light blinked 4 times and repeated this over and over
I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from WAUKEE, IA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Friction sleeve came apart ....would not hold door in place
Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maynard from WISDOM, MT
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not drain water
Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from NEPTUNE, NJ
- Parts Used:
- WPW10224430
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Soap Dispenser No Longer Functioning
Repair was easy. Step by step instructions on touTube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from OXFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drain pump noisy, broken piece of glass caught in pump.
removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from SAN DIEGO, CA
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replacing
The old filter simply unscrews and the new one screws in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dylan from RIVERSIDE, CA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher not draining on final cycle and smelled of burning
I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from KENNESAW, GA
- Parts Used:
- WPW10340683
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water trickling out of sprayer on top rack not strong enough to clean dishes. The back of the water manifold was broken off.
Removed top rack from dishwasher by removing retaining clips on roller track and slide top rack out of tracks. Placed top rack on table upside down and popped water manifold out and snapped new one in place. Install rack in reverse order of removal.
Note: Make sure there is no food debris clogging spray arm, that will give same symptom as well as a weak or clogged pump.
Note: Make sure there is no food debris clogging spray arm, that will give same symptom as well as a weak or clogged pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from HIGHLAND, NY
- Parts Used:
- WPW10317197
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Arm did not turn!
Removed old arm and put knew one on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from BATON ROUGE, LA
- Parts Used:
- WP8268961
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher door drops quickly to wide open position when unlatched
Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Open dishwasher door.
Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.
Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.
Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.
Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.
Repeat for right side of door.
Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.
Slide the dishwasher back to the original position under the counter top.
Insert the screws in the top brackets to secure the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Redmond, OR
- Parts Used:
- WPW10224430
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
soap dispensor door was warped
The repair was easy, no instructions with the part. I had a bad leak the first go round, found out that I did not have it centered with-in the indentation on the door panel, so I got to install it twice.
Was this instruction helpful to you?
Thank you for voting!