ADB1500ADS3 Amana Dishwasher - Instructions

followed directions, a kid could have done it,

Remove upper rack slide rail end cap and remove broken bracket. I used a butter knife to pry the end cap off. The bracket was already broke. so it came right out of the slide assembly
I installed the new upper rack wheel assembly into the slide assembly, and re-attached the wheel bracket to the upper dish rack assembly.
I looked at the other side for comparison to make sure I was doing it right. Everything went smoothly & all parts snapped into place like they's suppose too. "And just like that, I was done, and the dishwasher was fixed." :=) easy peasy.. If you have a computer to bring up the illustrations for reference it helps but is not necessary. The other side is also a good reference... Put them repair guys out of business.

New one snapped right into place.

Remove and replace by hand, no tools required

I watched a quick video and replaced it in less than 5 minutes. Video suggested removing the rack.....but I didn't even need to do that.

It is easy to change out the part. It seems though the part does not freely spin like it should. Does not seem to be warped but does not free spin.
Maybe the new part does not match??

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb

I just snapped the old one off and snapped the new one on..

Pulled out old gasket, pressed in new starting middle top. No more leak.

I watched the video supplied by PartSelect at time of purchase. The video was perfect. The installation couldn't be easier. The part arrived just in time. We had a family dinner that night. Dishwasher was back up and working again in 7 minutes.

Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.