ADB1500AWQ2 Amana Dishwasher - Instructions

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

I had two problems with the dishwasher. The latch handle was broken and a line crack developed on the control panel just above the handle area.

1. Ordered the Latch Handle (LATCH ASSY (BLACK) MA) (Series 10); Part # PS1559543 from PartSelect. (Maytag’s part number is 99003347). PS1559543 received from PartSelect includes the latch, latch handle, and two switches.
2. Disconnected power to dishwasher. (I put the washer on timer mode; the control panel lighted up; turned off power supply at the circuit breakers box; control panel light was off; confirming that power was cut).
3. Opened the door, removed the torx T-20 screws from the inner panel (I used a cordless drill and one of the star shaped screw tip from a cheap Craftmans screw tips set)
4. The inner panel slid down down enough to expose the latch assembly. Since the latch assembly was held in place by the two of the screws removed, it was now only attached to two sets of wires through the switches on both sides of the latch assembly.
5. The next thing to do was to connecting the wires to the new latch assembly. I chose to use the switches on the old latch assembly. There were plastic hooks holding them in place. The switches readily slid out by slightly push back the hooks. There is a little knob on the switch, and had to be pushed back to slide into the new latch assemble.
6. To fix the line crack, I used a toothpick to apply plastic glue on both sides of the crack. Then lined up the latch assembly with the control panel and the dishwasher’s inner internal panel, put back the two top middle two torx T-20 screw to hold them in place. Excess glue was wiped off with paper towel wet with isopropyl alcohol. This saved me the expense of ~$60 for a new control panel. Don’t use crazy glue, it will discolor the plastic.
7. Put back the screws at four corners, then the rest. I set the clutch of the cordless drill at 2 so that the screws were not over tightened.
8. Let the glue dried overnight. The crack was fixed, the latch assembly works like when the dishwasher was new.

After checking repair places who wanted $140-$200 to repair the handle (most of it labor and transportation of course) I checked this website and read the do it your self testimonials the first one being wendy from florida and figured if she could do it so could I. . . Wasn't quite as confident as her so found a handy person (charged me $30). It was a "piece of cake" -- remove the 11 screws (allen screwdriver), unclip the wires to the handle (pliers), clip in the new one, replace the screws. I could have done it myself. Took 15 minutes.

1. Removed door inside plastic panel, 2. Removed additional screws holding panel to hinge brackets and control panel, 3. Figured out that this would all have been easier if I'd unhooked door hinge springs first (access from sides), 4. Removed isulation from old panel and reglued to new panel, 5 Reassembled, hooking up door springs last. Voila!

I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.

Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen screws in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...

Took off broken handle and replaced it with the new one.

replaced rack

Turned off the power at the panel board. Took off the front panel. (The screws are torque screws, so you need that kind of driver). Removed the two electric leads. They are just connector type leads going to the switches. Pluged the leads onto the correct sides of the new latch assembly and reversed the procedure to put the panel back in place.

Removed 10 torx head screws from around perimeter of door (two of these screws hold door latch and handle). Unplug two wires from handle assembly and replace old handle with new. Reinstall 10 perimeter screws and job is complete.

Pulled out the old one and put in the new one!

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.

removed all door housing scews,removed old handle and wires and installed new 1,screwed housing back on,done

Removed the front door cover (held by several screws) Replaced the broken latch with the replacement by reconnecting the switches (one at a time & noting their orientation). Rescrewed the cover. Works like a charm!