ADB1500AWQ1 Amana Dishwasher - Instructions

1st: Unscrewed the inside of the door (actually hex screwdriver needed).
2nd: Removed broken part (one side of handle latch (which is plastic) was broken.
3rd. Had to disconnect two electrodes that were attached to the part that held the handle (there are two small prongs that you need to push back to remove these)
4th. In order to place the handle on the groove, you need to pull apart the bottom of the housing piece (it looks like it would be a hinge, but you just pull it apart)
NOTE: Make sure you have another person hold the top portion when you pull this apart because it has a spring and will come completly apart. This happened to us and it was a pain to get it back together.
5th: place the smaller "clamps" plastic pieces in the grove and then it should slide down into the groove, which will also seat the outer "plastic clamps" into the grooves.
NOTE: It seems like the repair part was built to reinforce this part of the handle, since this was the part that broke before. It is now reinforced with a little metal rod on each side.
6th: After all that, you need to place the two electrodes back on the piece.
7th: Hold it in place and put the inside of the door back on (start a screw on one side and then go to the opposite side. This will help to align the screw holes).
8th: After I put it all back together, I turned it on to make sure it worked ok.

This repair was very easy. First, I opened the dishwasher, removed the screws (they are torx) and removed the old handle assembly. I removed the inner liner from the door, and to do that I had to pull out the electrical wires. I turned off the power, always a good idea. I should have marked the polarity on the plugs before removing them, since you can put them back on wrong (and I did).

I also used caulk to hold the assembly on the bottom, since the cheap plastic molded forks holding the assembly on had broken. Most of the holding force comes from screws at the top. The caulk provides just a little adhesion, and will be easy to remove if the handle should need to be removed again--which I consider unlikely.

This was a very easy repair. Before I did anything, I flipped the breaker for the dishwasher and tried to turn the dishwasher on to make sure it had no power going to it. Once I was certain the power was off I removed the hex screws (there are 11) on the inside of the door panel using the hex screwdriver. Lifting and holding the inside panel up, I then used the pliers to pry the old latch assembly out of its metal prongs. Then I replaced the old latch assembly with the new one, pushing the metal prongs (by hand) into the slits of the new latch assembly. Last, I lined everything up and screwed the door panel back in place. I flipped the breaker back on and activated my child lock to make sure I had power. The handle worked perfectly. Quick and easy fix!
I ordered the part with 3-5 day delivery and actually received it in 2 days! I'm extremely pleased with my partselect.com experience and highly recommend using them for all your appliance parts needs!

I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.

This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.

Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.