ADB1500AWW2 Amana Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Pittsburg, PA
- Parts Used:
- WPW10130695
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broken Latch on my Dishwasher
1 - Unscrew the back of the dishwasher with a hex-type driver. The latch assembly will be resting inside the outer door assembly. Make sure power is turned off to the washer - there are a couple of "hot" wires that will attach to the latch assembly.
2 - Unplug the wires from the old latch and plug into new latch assembly.
3 - Place the latch assembly back in place and re-attach the two door pieces together.
4 - Turn power back on at the breaker.
5 - Load dishwasher with the stuff that's been sitting in your sink.
6 - Gloat to spouse/significant other that you just saved $100 by fixing it yourself.
Just a quick note of thanks for shipping the replacement handle for my Maytag dishwasher. Service was superquick and I was able to save big bucks (no service call). I called on Saturday evening and the part was here on Tuesday. The young lady who helped me was awesome and a Pens fan to boot. I seldom send these types of emails but my experience was worth sharing.
2 - Unplug the wires from the old latch and plug into new latch assembly.
3 - Place the latch assembly back in place and re-attach the two door pieces together.
4 - Turn power back on at the breaker.
5 - Load dishwasher with the stuff that's been sitting in your sink.
6 - Gloat to spouse/significant other that you just saved $100 by fixing it yourself.
Just a quick note of thanks for shipping the replacement handle for my Maytag dishwasher. Service was superquick and I was able to save big bucks (no service call). I called on Saturday evening and the part was here on Tuesday. The young lady who helped me was awesome and a Pens fan to boot. I seldom send these types of emails but my experience was worth sharing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jacksonville, FL
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Latch wouldn't function
I learned everything I know about the procedure from this site. but here it goes:
Turn off the power at the breaker! If you are like me, you will forget until you are trying to change out the wires and then ZZZTT! you will jump and say somehting your kids should not hear. (like I did).
After forgetting to turn off the power, I unscrewed torx-head screws (its a T-20 driver if you need to buy it --T is for torx and 20 is the size) around inside edge of door to remove the inside door panel. Take care when opening the panel because some wires are still attached to it.
Removed old latch assembly by unplugging it. Normally, the black and white wires would unclip from the assembly, but in my dishwasher, the "quick release" wire connectors going to the latch assembly were not coming apart. The wire connectors themselves were attached to two small switches on the latch body, so I just took the switches and wires off the latch assembly by gently prying the 2 retaining clips away from the switch and they come right off, with the wires still attached. I then removed the switches from the new latch assembly, so I could plug it in to the old wires/switches dangling from my dishwasher. Then I got a mild shock, and sent the kids out of the room.
I was pretty sure there was nothing wrong with those switches--it was pretty obvious that my problem was mechanical, but I saved them just in case. The latch handle itself had broken on one side. Also, upon opening the panel, I also discovered that the latch assembly was no longer securely attached to the control console--the tiny plastic mounts (about 1/16th of an inch wide) that held the latch assembly at the bottom were broken. Surprise surprise.
I took the advice of a poster here to use JB weld to secure the new latch assembly to the console where the flimsy plastic mounts had been. (instead of spending $80 for a new control panel just to get new flimsy mounts).
The latch assembly went right into the old spot. Use a hand driver or set your drill on a low clutch setting so as not to strip the screws going back in--remember, its plastic! The biggest investment here is time--unless you don't have the torx driver.
On a related note, this Maytag is only about 3 years old and already I have had 2 broken rollers on the upper rack and now the latch. I went to the hardware store and bought a couple of 99-cent cabinet knobs that were approximately the same size as the rollers I had to replace. I ground the knobs down to fit in the slide, and then screwed the knobs onto the rack. It took some machining, but it sure beats the $35 (each side!) for the replacement roller mechanism!
Have a great day and I hope this helps someone!
Turn off the power at the breaker! If you are like me, you will forget until you are trying to change out the wires and then ZZZTT! you will jump and say somehting your kids should not hear. (like I did).
After forgetting to turn off the power, I unscrewed torx-head screws (its a T-20 driver if you need to buy it --T is for torx and 20 is the size) around inside edge of door to remove the inside door panel. Take care when opening the panel because some wires are still attached to it.
Removed old latch assembly by unplugging it. Normally, the black and white wires would unclip from the assembly, but in my dishwasher, the "quick release" wire connectors going to the latch assembly were not coming apart. The wire connectors themselves were attached to two small switches on the latch body, so I just took the switches and wires off the latch assembly by gently prying the 2 retaining clips away from the switch and they come right off, with the wires still attached. I then removed the switches from the new latch assembly, so I could plug it in to the old wires/switches dangling from my dishwasher. Then I got a mild shock, and sent the kids out of the room.
I was pretty sure there was nothing wrong with those switches--it was pretty obvious that my problem was mechanical, but I saved them just in case. The latch handle itself had broken on one side. Also, upon opening the panel, I also discovered that the latch assembly was no longer securely attached to the control console--the tiny plastic mounts (about 1/16th of an inch wide) that held the latch assembly at the bottom were broken. Surprise surprise.
I took the advice of a poster here to use JB weld to secure the new latch assembly to the console where the flimsy plastic mounts had been. (instead of spending $80 for a new control panel just to get new flimsy mounts).
The latch assembly went right into the old spot. Use a hand driver or set your drill on a low clutch setting so as not to strip the screws going back in--remember, its plastic! The biggest investment here is time--unless you don't have the torx driver.
On a related note, this Maytag is only about 3 years old and already I have had 2 broken rollers on the upper rack and now the latch. I went to the hardware store and bought a couple of 99-cent cabinet knobs that were approximately the same size as the rollers I had to replace. I ground the knobs down to fit in the slide, and then screwed the knobs onto the rack. It took some machining, but it sure beats the $35 (each side!) for the replacement roller mechanism!
Have a great day and I hope this helps someone!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Wheaton, IL
- Parts Used:
- W10280784
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack had rust spots.
You just remove the old unit and set in the new unit. the wheels were already connected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Cupertino, CA
- Parts Used:
- WPW10130695
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Handle Broke
After checking repair places who wanted $140-$200 to repair the handle (most of it labor and transportation of course) I checked this website and read the do it your self testimonials the first one being wendy from florida and figured if she could do it so could I. . . Wasn't quite as confident as her so found a handy person (charged me $30). It was a "piece of cake" -- remove the 11 screws (allen screwdriver), unclip the wires to the handle (pliers), clip in the new one, replace the screws. I could have done it myself. Took 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCHESTER, MA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking door
easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janis from Bryan, TX
- Parts Used:
- WPW10130695
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Black Plastic Door Handle Broke Off
First, unplug your dishwasher from under the sink. Remove all eleven screws from the inside door panel. Lift door panel up. Old latch should lift right up. use a pair of pliars to grab and squeeze the base of the old metal connectors to pull out. Do not pull on the wires themselves. Plug in the new connectors from the new latch assy, fit into place, replace the inside door panel/screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Arlington, VA
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Handle to dishwasher was broken.
Not bad at all. Took inside door panel off. Removed broken part. A little tricky to remove/replace the electric nodes. Decided to use the old ones rather than using the new ones that came with the part. Just easier than removing wires. Put door back together with new handle in place. Good to go...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HILTON HEAD, SC
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher won't run; no response from control panel.
I assumed the broken door latch was causing the problem and not allowing the switches to make contact. Replacing the latch assembly was easy, but did not fix the problem, which must now be either the printed circuit board or the control panel. Either one is too expensive to justify spending on a machine that is several years old. In retrospect, an additional step in troubleshooting would have kept me from wasting time and money on the new door latch. I suggest that if you suspect the door latch is the problem, remove the screws holding the inside door panel, lift the switch assembly out of the door and insert it into the latch. See if you are getting 120 volts to the printed circuit board. If you are, but there is still no response from the control panel, the problem is not the door latch (even if it is broken, which they frequently are). Good luck figuring out if it is the printed circuit board or the control panel. At this point I decided to replace the machine with a basic Frigidaire model that used the old-fashioned timer switch. The last time I owned a machine like it, it lasted over 20 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from BOLIVAR, OH
- Parts Used:
- WP99003446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cable broke
Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from BAYTOWN, TX
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken handle
Removed the interior of door to get to latch. Removed broken latch and unplugged the wire after I turned off electricity. Reinstalled the new latch and interior door and turned the electricity back on and everything worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from S CHARLESTON, WV
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Door latch was broken
This is a simple repair once you conquer the problem of removing the wire clips from the old switches. And conquer I did. All you need are regular and needle nose pliers, and a heavy pot or pan. Start by turning the power off and then remove the screws holding the inner door. Carefully lay the inner door to one side of the outer door and place a heavy pot or pan on the outer door to hold it down. The handle assembly is held on with screws removed from the inner door, so you can now lift it out. Check that there are no small broken pieces anywhere on the door. Use a marker to mark Right and Left on each clip.Then remove each old switch from the old handle assembly by carefully bending the two small clips on each switch back to release it and wiggle it free with the wire clip still attached. The wire clip is actually a one piece plastic cover. Then, do this: grip the old switch with the regular pliers and then slide the unopened point of the needle nose pliers between the switch and the wire clip; there is plenty of room. This will put sufficient pressure on the wire clip to slide it from the switch. Do not grip the wire clip with pliers, it will break. Once off, put the wire clips on the new switches and install the handle. Reinstall the inner door and test the handle. That should do it. A leisurely 20 minute or so repair job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from Reseda, CA
- Parts Used:
- W10283681
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Water not heating
Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer
Elmer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Round Rock, TX
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Handle was broke
Removed the old part (about 10 philip head screws).
Waited 1 day for the new part.
Unplugged the old part and plugged in the new part.
Job done.
* Partselect was GREAT. They had repair stories that made this job easy (told how to do it). They delivered the part very fast. They were way under priced to other parts places.
Waited 1 day for the new part.
Unplugged the old part and plugged in the new part.
Job done.
* Partselect was GREAT. They had repair stories that made this job easy (told how to do it). They delivered the part very fast. They were way under priced to other parts places.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Raymond, ME
- Parts Used:
- WPW10130695, WPW10261227
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Latch handle was broken not allowing the diswasher to lock and wash dishes.
On a Saturday my wife set the dishwasher to wash. The door handle had not properly shut and we discovered the dishes had not been washed. After the threat of handwashing and realizing that the latch assembly wouldn't engage, I decided to take apart the inside front cover and look over the problem. Screws easily came out and inside cover lifted up but not off since it was connected to the handle assembly. Realized the plastic outside handle was broken and wouldn't allow the locking mechanism to engage. Went on PartsSelect.com, found the model and ordered the new handle. I paid the lower shipping costs but the new part arrived very quickly - one day. Relatively easy to assemble. Turn off power, take out inside door screws, disconnect handle assembly. This was the hardest part, required pliers to pull the wires off (note: mark connection sides for reassembly). Installed new handle, wire connections easily seated, put back three screws, turned on power and verified dishwasher would run, installed remaining screws and set dishwasher on. Took about 15 minutes and the part was a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from brooklyn, NY
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
door handle broken.
Removed all the screws from the door panel. Removed door handle. Replaced it with new handle. Attached switches but did not turn the power off. Replaced the panel. Everything fitted well and works well.
Was this instruction helpful to you?
Thank you for voting!