ADB2500AWB1 Amana Dishwasher - Instructions

unscrewed the door panel, installed new handle. Pretty straight forward.

The reason this story is important is the purchase of the part was more difficult than the repair. Original attempts from another company had the wrong part delivered three times. I was ready to give up until I recieved help from PartsSelect.coms professional sales people. I recieved the correct part the first time. The repair was completed by first securing electrical power to the unit. I was able to isoplate the breaker which feeds this appliance. I removed the 10 Screws from the inner door panel to gain access to the latch and Control Panel. Using two(2) small blocks of wood I was able to prop the innner door and latch assembly up away from my work. I then removed the two screws which hold the control board to the panel and disconnected the ribbon cable attached to the control planel from the control board by pulling straight out on the cable. I was then able to remove the broken control panel and replace it with the new one. The control panel was held in place by four (4) screws.
CAUTION: Do not overtighten screws going into the plastic control panel it will crack. Reassmbly was accomplished in the reverse order with the following steps modified. To reconnect the ribbon cable to the control board it was easier if I removed the one screw holding the Top Housing board from the Control board. I was able to reinsert the ribbon cable by pushing the cable straight into the connector. I then reconnected the the Top housing board to the control board. The other step that required care was insuring the latch assembly holes lined up correctly and the latch was properly aligned for assembly. The rest was completed in reverse order.

First of all, Partselect is definately has the cheapest price and quickest processing and shipping that I found. No im not getting paid for this. Anyway, Be sure to kill all power. Pulled the inside cover off, carefully not pulling wires apart. The handle assembly fell to pieces. There are two wire harnesses (minor current)that you need to disconnect and reconnect to new switches. Align mounting holes and insert screws. Replace inside panel and screw tightly and fix is complete.

First I turned the power off at the elecrical panel. (there are live exposed parts on the inside of the door if you don't turn the power off and they conecet to the handel ) Then I removed the 9 or 10 tork screws that holds the inner part of the door to the outer part of the door. (Screws are on the inside of the door.) When you remove the screws this also losenes the bracet that hold the handle assmbley disconect the wires then put in the new one. the wires are a little hard to disconect. but that is about the worst of it . This part comes with every thing and and is cheper then buying it seperat. Sorry about the spelling. hope this helps

Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.

The exterior lift handle had broken on both sides where it rotates and presses against the internal release mechanism. Eleven screws held the door panel together and also the lift handle/latch assembly. The new assembly dropped right into place. But it had microswitches already installed and I wanted to use the old ones since it was very difficult to pull off the wires. To install the old microswitches requires that you hold down each switch button so that the switch will fully clip into place. Next I put all the screws (torx type) back in

Amana itself was the biggest issue, not all screws holding cover matched, must have been assembled on a Friday. The electrical connections were a problem too. Being a built-in I couldn't unplug the unit, never thought about the breaker. I got reminded a couple times they were live, and didn't separate easily. Replacing the cover was much easier, had to reposition it a few times for latch to work freely.

Turned off power removed back of door removed handle disconnected leads replaced

simply pulled out old one slowly inserted new one (stretching slightly) Presto done

The upper arm assembly removes easily by unsnapping a plastic part or two that holds it in place.
Once the arm assembly is removed, you simply remove the screw that holds the arm on, replace the arm, and replace the screw. The key thing here is that you need a "star drive". This is a screw driver or bit that has a star shaped end. I don't know what size it is.

I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!

The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.

The arm has a small bracket that can snap off and on the main water tube easily without tools.

Changing it was a snap!

I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.

Removed the old one....slid in the new one.

In the back of the dishwasher there are two docking stations for the racks to go into for the water to flow to the rack spinners. These stations have rubber gaskets and flaps in the back that totally wear out. Where our problem was mostly the top rack at first I just replaced the top one and the dishes got cleaner but not perfect. So then I ordered the second one and replaced that one too, now the dishes are perfectly clean all the time!! I would suggest replacing both at the sam time. Just pull off the old part and snap the new part into place. No tools needed. Have to remove the top rack to replace that one. The bottom one could be replaced with the rack pulled out. Thank goodness for Parts select!! This has been the worst dishwasher ever and I have replaced so many parts throught Parts Select. My $189 dishwasher I had before this high end dishwasher was much better-- I know why Maytag got bought out--poor quality!

unscrewed the panel unhooked handle installed new one