ADB2500AWQ2 Amana Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Sweeny, TX
- Parts Used:
- W10862259
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher door latch broke and would not open
MAKE SURE ELECTRICITY TO DISHWASHER IS OFF!!! If dishwasher is installed directly wired, TURN OFF THE BREAKER!!! Undo the inside plastic door molding....remove the old latch and install the new one! Easy to install! Wife is very happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Sarasota, FL
- Parts Used:
- W10862259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken latch handle
Removed screws to the door and took out broken handle and replaced it with the new handle. Replaced screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SPRINGFIELD, VA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher leaking.
Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Orlando, FL
- Parts Used:
- 99002659
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Wouldn't wash dishes
I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.
Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LOMBARD, IL
- Parts Used:
- W10862259
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door handle would not close so washer would not operate
I removed the 8 or so screws from the inside of the door. I then slightly pulled back the inside panel of the door exposing the black and white wiring connections to the handle. I removed the bad handle with the wires still connected and then disconnected the black and white wires one at a time and connected them to the new handle, making sure the handle was oriented correctly, handle facing outward. I then removed the bad handle. I put the new handle in place and put in the screws half way into the holes that go through the inside panel into the new handle. I then re-installed the screws from the bottom inside of the door going from the left side to the right and then back like you would lace a shoe until all of the screws were in and tightened and later tested the washer successfully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from Greenville, MS
- Parts Used:
- 99002659
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwashwer stopped spraying water
I'm telling this story for my husband who is a pretty handy guy--I watched him do the repair. I had had someone out to look at the dishwasher and they said it would be $284 to fix this one little thing because you couldn't buy the one little part separately, you had to buy a whole new motor. Since the dishwasher is old, it didn't make sense to invest this much in it--might as well buy a new one for that kind of money. My husband did some looking around and found the part on your site and installed it himself. So the cost was under $40. The dishwasher is now working better than it had been for a while.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert d from MOORHEAD, MN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door didn't seal tight. So when it would go into rinse mode it would leak water on my floor
The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from CARROLLTON, GA
- Parts Used:
- W10862259
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No problem very easy
I am 77 years old so I had my daughter help. We turned off the power unplugged the old handle & wiring & plugged in the new one. Put the back on and I was ready to wash dishes. Thank you for sending my order so fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LANGHORNE, PA
- Parts Used:
- W10862259
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken handle
unscrewed the panel unhooked handle installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pamela from WEYAUWEGA, WI
- Parts Used:
- W10862259
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broken
Unscrewed inside door of dishwasher and remived handle. Ordered new handle and when it arrived i reinstalled same way i took out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BLUE SPRINGS, MO
- Parts Used:
- WP6-917644, WP6-917642
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
WAS NOT GETTING DISHES CLEAN
UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from VANCOUVER, WA
- Parts Used:
- W10862259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
handle broke, second time
unscrewed the door panel, installed new handle. Pretty straight forward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Lemont Furnace, PA
- Parts Used:
- 6-919804
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fist the lat broke, in an attempt to repair the latch three(3) 0f the plastic parts for the screws cracked.
The reason this story is important is the purchase of the part was more difficult than the repair. Original attempts from another company had the wrong part delivered three times. I was ready to give up until I recieved help from PartsSelect.coms professional sales people. I recieved the correct part the first time. The repair was completed by first securing electrical power to the unit. I was able to isoplate the breaker which feeds this appliance. I removed the 10 Screws from the inner door panel to gain access to the latch and Control Panel. Using two(2) small blocks of wood I was able to prop the innner door and latch assembly up away from my work. I then removed the two screws which hold the control board to the panel and disconnected the ribbon cable attached to the control planel from the control board by pulling straight out on the cable. I was then able to remove the broken control panel and replace it with the new one. The control panel was held in place by four (4) screws.
CAUTION: Do not overtighten screws going into the plastic control panel it will crack. Reassmbly was accomplished in the reverse order with the following steps modified. To reconnect the ribbon cable to the control board it was easier if I removed the one screw holding the Top Housing board from the Control board. I was able to reinsert the ribbon cable by pushing the cable straight into the connector. I then reconnected the the Top housing board to the control board. The other step that required care was insuring the latch assembly holes lined up correctly and the latch was properly aligned for assembly. The rest was completed in reverse order.
CAUTION: Do not overtighten screws going into the plastic control panel it will crack. Reassmbly was accomplished in the reverse order with the following steps modified. To reconnect the ribbon cable to the control board it was easier if I removed the one screw holding the Top Housing board from the Control board. I was able to reinsert the ribbon cable by pushing the cable straight into the connector. I then reconnected the the Top housing board to the control board. The other step that required care was insuring the latch assembly holes lined up correctly and the latch was properly aligned for assembly. The rest was completed in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- russell from manchester, TN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
door latch broken
first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Solon, IA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Broken Door Latch
Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.
This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.
This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.
Was this instruction helpful to you?
Thank you for voting!