ADB2500AWS37 Amana Dishwasher - Instructions

first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam

Removed inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.

Took a while to figure out what had to be done. Brackets have to go under the metal frame which involves dropping the compartment. That is done by removing the screws which are hidden under the door gasket. Once I knew what had to be done it was simple.

After disassembling accumulator assembly looking for reasons that washer not washing properly, I noticed accumulator filter had failed. The plastic (or whatever material it is) covering the holes was torn in a couple of different holes. Realizing that this was not the reason for the loss of pressure I investigated a little more and found that water arm going into the docking station was extremely worn with much play. Water pressure was compromised because of it. I replaced filter and docking station and now its like a new dishwasher again. Saved a dishwasher from the landfill!

Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.

I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.

Dishwasher is in our summer cabin in Colorado so everything has to be drained for the winter. Not really sure whether this leak was freeze caused or that the valve was just old. Couldn't find a crack when I got the old one apart; might have been just an O ring needed. Anyway, just follow the video provided by this site for replacement of the valve; really easy. Biggest hassle for us was getting the dishwasher out (and back in) as it was wrapped in insulation which made the fit really tight. Thought I had everything I needed when I started but didn't have teflon tape which is needed for the brass fitting connecting the water supply to the valve (fitting is in your old valve and will be reused with the new one).

1. Shut off water supply

- Remove water line and drain hose if you need to. I was able to simply move the dishwasher forward some to do this repair without disconnecting

2. Remove access panels on the bottom.
3. Open the door
4. Remove Door Gasket carefully (do not stretch)
5. Use torque 20 driver to remove 6 screws that were under the gasket

- Some of the screws were rusted for me so I had to use kroil, a pick to clean out rust, and a hammer to help get the torque driver in enough to remove the screws. A local hardware store had replacements.

6. Use Phillips screwdriver to remove screws holding mounting brackets
7. Carefully move dishwasher out some (Careful if you have a copper water hose you may want to disconnect it)
8. Remove the strike if it is attached above the metal bar
9. Lift the metal bar and push down on the tub to make room to remove the old mounting brackets (slide them up, forward, and to the side)
10. Put new mounting brackets in place (put mounting bracket under bar, slide over into place)
11. Reverse the order at this point.

Be careful not to stretch the gasket. I soaked mine in vinegar for a bit and gently washed with dish soap to remove deposits.

n/a

followed video provided,simple job and cured problem

We unscrewed the inner door panel and pulled it apart, disconnected the wiring, removed the screws holding the dispenser in place and swaped it out. One problem we had putting everything back together was that the latch for the door didn't line up and we couldn't shut the door but we simply unscrewed the door, readjusted the latch and put it back together. Works great now!