ADB1400AMS0 Amana Dishwasher - Instructions

Replaced door balance link kit and door opens easy does not squeak or slam down.

Video was great help. Replacing the balance parts was easy. My wife and I are in our 80's. Mobility is difficult when it comes to working on the floor. Between the two of us we spent the majority of our time just getting up and down,

The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

Pretty easy for the parts. Taking the dishwasher out is the hard part. Typically, you should be able to unscrew the 2 screws holding the dishwasher to the underside of the countertop and then slide out the dishwasher to expose the cable assembly - but you also need to unplug the unit (unless it is hardwired), disconnect the hot water supply line from the angle stop (remember to turn off the angle stop) and sometimes disconnect the drain line from the vacuum breaker or garb disposal. You need to disconnect these things so that you can move the dishwasher out far enough to be able to see the entire right and left sides of the dishwasher. Once that hard part is done, you use a hex driver to remove the old cable pulleys, put on the new cable pulleys, and then feed the light weight cable through the pulleys - the end with the big plastic thingie attaches to the door and the other end attaches to the spring. Then you grab the spring and manhandle it onto the back end of the dishwasher chassis (look for the small hole in line with where the cable would line up. Careful as the spring attachment step could result in an injury - Hope this helps.

Started the rope onto the top holder, threaded the rope around the rollers and using the pilers pulled the spring forward to attach the other end of the rope.

just move the machine out and replace the string. this site is very reliable and and great company. since the dishmachine door cannot be closed, we first order door strike, ,,,, still doesn't work after installation. and return all parts and order the balance kit, now works fine after. we appreciate your help

Followed directions here. Extremely easy repair.

Watched YouTube first of course. Pulled off the old gasket, found the center of the new gasket and started installing the gasket from the very top and all the way down the sides. I made sure it was in tightly and smooth. No more leak, should have listened to my wife sooner!

pulled it out, saw 'pulley' was fine, and put cord on spring and puled it enough to hook it on other end.end after running cord around the 2 pulleys, as it was on the other side. push it back and done.

Just like the video; remove the 2 nuts off the kick plate, remove the 2 screws under the counter, pull the unit out, ease the spring off the cable, nut drive the pully assembly's off, install the new ones, place new rope/cable from the door arms onto pullys, attach the spring, push the unit back into place, replace screws and the kick plate. Took 15 minutes.

Shut off power to dishwasher.Pulled dishwasher half way out from cabinet, careful not to disconnect waterline, drain-line, and electrical connections. Replaced roller assemblies and connected new door balance links to springs as shown in the great video featured on your website. Thank you for the great pricing, speedy service, and the install instructions. I am happy!

I watched my son as he pulled dishwasher out part way. The space was a little tight, but he did a fine job of replacing with a new string.

Step 1. Cut off water supply. Step 2. Remove two screws from bottom plate to remove the plate. Step 3. Check that drain line and power supply have enough slack to move the unit out from under the cabinet. Step 4. Remove two screws from top frame that secure the unit to the cabinet framing (note my counter-top is granite so framing goes across the top of the unit; so units are secured directly to the countertop). Step 5. Disconnect water supply line and place something, i.e., a plate, old towel, etc. to catch excess water in the supply line. Step 6. Lower leveling feet to provide clearance to remove the unit. Step 7. Pull unit carefully from under cabinet to access both sides so Door Balance Link Kit is accessible, checking for tension on drain line and power supply line (see Step 3.) as you are pulling out the unit. Step 8. Remove broken Door Balance Link Kit (pay attention to how the rope is positioned around the pulleys; using your phone to take a picture before you disassemble the kit is a good idea). Note-the replacement kit is different in design/appearance (not function) from the OEM part. This should be clearly stated in the "Description" paperwork accompanying the part but it is not. Step 9. Install the new Door Balance Link Kit exactly as the replaced one. It is important to note that there was no spring tension when the broken part was removed so re-attaching the part with the spring attached takes some strength because of the tension. I recently (9 weeks ago) had two brain surgeries; my right arm was paralyzed following the second surgery. Although I am recovering fine, I have not gained my hand strength back completely. I used a screwdriver to stretch the spring back to the attachment point which allowed me to slip the spring into the hole. If you have to use this method or a similar technique, use extreme caution. The spring is strong and if it slips could cause an injury or damage. I strongly suggest that while the unit is out that you replace the other (non-damaged) Door Balance Link Kit. It's had the same wear as the broken and its likely to break soon. Again, if you have the hand strength to remove the spring by stretching it to disconnect it, that is the best approach. But, if you do not have the hand strength, simply take a pair of channel-locks, grasp the end of the spring to stretch the spring to remove tension on the rope and hold it while cutting the rope. Release the tension on the spring and repeat steps 8 & 9 to install the second kit. Step 10. Move the unit back into position to attach the water supply line and then attach the water supply line. Step 11. Carefully reposition the unit back into place checking to make sure the water line, drain line, and power supply are not crimped. Step 12. Once in position, use leveling feet to raise the unit to its proper height while checking to make sure it is square/level. Step 13. Replace the screws removed in Step 4. Step 14. Run the machine through a quick wash before replacing the bottom plate to verify there are no water leaks, crimped hoses, etc. Step 15. Replace the bottom plate (see Step 2.).

Get a piece of stiff wire (medal close hanger) cut a Short piece and take a tool and roll a half circle on each end making the link length you need then attach the lanyard to the spring