DWCA500AAW Admiral Dishwasher - Instructions

I went to take the bottom front panel off and ended up dropping the screw down behind the baseboard and then found that I did not need to take the panel off. The broken end of the float was not obstructing and I was able to just drop the new float in place. I spent more time looking for a replacement screw than any thing else. Ran it and it works fine.

Followed the instruction video provided by this site ! 15 minute repair?..Super Simple!!! I Love this company!!! Saved me a bunc of money!!

My husband thinks I'm the smartest wife ever! He's telling all his friends how I got online to research the problem (thanks to your readers and DIY comments!), diagnosed it, ordered the parts and - voila - clean dishes once again! It's like everyone said, remove inside of the door by removing 7 torx screws, dismantle wiring -remember to note what connects to what - pop out old parts, easily insert new ones (that arrived in record time!), reconnect wiring, replace door and you're done. Replacing the reservoir o-ring also stopped the leaking problem that preceded the door issue. Thanks PartSelect!

First i bought inner door seal and that didnt work,so i read some of the other repair reviews and found that it was the soap cup latch gasket.When i removed the cover from the door you could see where the water and soap was getting in and running down to the lower right side of the door.Once i looked at the door latch gasket it was easy to see it was torn and worn out.I did replace all four gasket's just for assurance down the road.

Removed old gasket and simply replaced it with the new one. Very easy.

Removed the inside door panel. Removed the 2 mounting screws to release the latch retainer assembly. Used needle nose pliers to squeeze the posts to release the rinse aid actuator. THIS was the most difficult part since they are made of plastic (didn't want to break it). Removed the spring. Mine did not have a "pivot" to remove since it was a older model, but this would be removed next. Removed old gasket around soap door latch. Pulled tabs hugging the square wax motor actuator and remove. Removed the clear plastic slider. Pulled out the old door latch. Reversed process to put back together. Make sure the gasket around the door latch is pushed all the way down onto the slot of the latch. As a precaution, I also replaced the reservoir O-ring for the rinse aid tank which was quite worn as well. When it's all apart take the cap off the rinse aid reservoir and the reservoir container drops out super easy. That is where the O-ring is. Very glad they had the parts I needed!!

this is a portable unit
the wood top is removed this allows access to the side cabinet screws and the lower front trim screws behind the lower front trim panel you can access the hose connections disconnect and reinstall
new part works great!

Remove the motor and impeller housing assembly from the unit by disconnecting the motor wiring plug, green ground wire, removing the drain and transfer hose, wash arm assembly and three screws for the filter assembly. A plastic locking ring secures the housing assembly into the unit and is removed by rotating aft about an eighth turn. The impeller is removed from the motor shaft by unscrewing the left hand threads on the fan that attaches to the end of the impeller. The impeller has longitudinal splines that engage the motor shaft, so it has to be removed by pulling straight off of the motor shaft. My impeller was stuck on the motor shaft, so I used a dremel tool with a cut off wheel and sliced through the impeller to loosen it. Installed a new motor shaft oring, and then slid the new integrated seal/impeller onto the motor shaft and secured with the fan (remember left hand threads). Reassembled unit and no leaks...

no problems, very easy

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~

First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,

First I removed power to the dishwasher. The inside panel of the dishwasher door is held on with several screws with Phillips heads. Remove those and the panel comes off. There is a silver metal guard that you have to pull off being careful not to tear the insulation that is on the other side. Then there is one hex head screw to take off the handle latch assembly. You remove this assembly and take off the wires to the two switches on each side of the assembly. The replacement part doesn't come with the black plunger that pushes on the switch buttons so you have to remove it from the old assembly. This was the only difficult part, I essentially destroyed the old plastic assembly getting it out. But putting it in the new assembly was easy. Then I attached the wires to the switches in the new part and reassembled everything. Works like a charm now.

I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.