ADB1500AWB Dishwasher - Instructions

Received the entire latch/switch assembly rather than just the plastic latch handle. This was a pleasant surprise, especially for the price. The latch assembly was clearly a better designed and more robust assembly than the original.
Removed the inside panel of the door by removing the dozen or so TORX screws.
Pulled the inside panel away from the outside door panel (gently, cables attached) to gain access to the latch/switch assembly. A second set of hands was helpful for this and some following steps.
At that point the latch assembly was free mechanically from the door, but there were two wiring harnesses attached to the latch assembly via plug connectors to the two microswitches on the latch assembly. It looked like it was going to be easy to unplug the harness from the switches, but I could not do it. Never did figure out how to do it.
Removed the two microswitches (with harnesses attached) from the 'old' latch assembly by pulling back the plastic tab that holds each switch in place. At that point the rest of the latch assembly was completely free from the machine.
Removed the two microswitches from the 'new' latch assembly using the same method as above. This step requires care as the plastic parts and switches can be damaged.
Put in place the two 'old' microswitches with wiring harnesses attached on each side of the 'new' latch assembly. These snap in place. This requires care, as above, and the second set of hands to hold away the inside door panel.
Put the latch/switch assembly in place in the door, and put the inside door panel back in place.
Re-installed the TORX screws holding the inside door panel - and latch assembly - to the door.
I kept the 'new' microswitches because one day the 'old' switches may fail. If that happens and I want to replace the microswitches, I still don't know how I will remove the switches from the wiring harness. I guess I'll figure that out if the time comes.
Except for the difficulties disconnecting the microswitches from the harnesses, this was an easy and straightforward job. The latching of the door seems more positive, now, and the machine is working fine.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

A common theme you'll see thoughout the repair stories;

1. many broken handles at the hinge
2. TURN THE POWER OFF.

This assembly comes with the microswitches (which is not a bad idea to replace since they are electromechanical and will eventually fail). My only recommendation is to buy a couple of these handle assemblies because they WILL fail. I'm on my 3rd!

Door gasket fit in like a champ! No special tools required - just scissors to trim off the excess ends. Unfortunately this didn't correct the leak. The leak was caused by a Home Inspector who ran the dishwasher without soap. The soap has a defoamer in it. If you run the dishwasher without soap the water mixes with the surfactant in the jet dry and causes foam which results in a door leak. The foam also causes the pump to cavitate which is not healthy for the pump.

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.

Removed 11 T20 Torx head screws. Removed and replaced latch. Removed and replaced door seal and foam insulation strip - no additional tools required. Super easy to repair and didn't leak a drop afterwards.

Easiest repair ever! 11 sized T20 screws hold the plastic to the door. Remove those and the handle just sits there. Disconnect the leads from the old and attach to the new. Total repair time under 10 minutes, and I'm NOT a handy guy.

Unplug the power cable. Remove 11 torx fasteners holding the inner door panel. Remove two sets of wires from old opener and install the new door opener assembly. Replace all the screws. About 10 minutes with a power driver.

removed the screws that held the inner panel. removed the handle from its electrical connectors (2) reinstalled new unit and works like new.

In less than 5 minutes we took the screws out, fixed the latch and had it back together again. The amazing part of the story is the perfect diagrams and helpful instructions from Part Select. I ordered the part one day and by noon the next day the dishwasher was fixed!

I originally ordered the incorrect piece via the website, however when calling PartSelect to return the part they informed me that they could help me find the correct piece which they did. The correct piece arrived within 4 days. It was easy to install. The part works well. I'm very happy with the customer service.

I first listened carefully and noticed that during cycling, the electric motors could be heard starting, stopping, and apparently running normally during both wash and emptying cycles. However, no water was being pumped around during the wash cycles, while emptying (which uses a different motor) worked normally throughout all cycles. Thus it seemed to me that the electronic programming was working correctly in turning both motors on and off as necessary. So I figured somehow the wash motor impella was not turning and pumping water, despite the fact that the motor was indeed running correctly. So I removed all the plastic housings, the screwed on impella, and the metal chopper at the base of dishwasher. Then I was able to easily pry the old plastic chopper sleeve right off of the electric motor shaft (normally it is screwed on and cannot be pryed off). Since the plastic threads inside the chopper sleeve were completely stripped, the motor shaft would turn but the impella would slip on the shaft and not be driven. The replacement sleeve was much better constructed (metal not plastic). It could be easily screwed on to the motor's driveshaft after lifting the old rubber seal and gently holding the motor shaft with a pliers (carefull to avoid scratching the shaft). I removed the old rubber seal nd replaced it with the new one from the kit, right over the newly installed metal chopper sleeve. Next, I easily centered the metal chopper sleeve and pressed in the new seal after reinstalling the plastic/metal chopper screen, using the temporary jig included in the kit. Then the jig was discarded and the impella simply screwed onto the chopper sleeve (using the appropriately threaded hold-down screw provided in the kit). Finally, the rest of the plastic hardware is screwed in place. Waahhlaa...now impella is motor driven again and blows water hard into the dishwasher during the wash and rinse cycles. Total cost of job to do-it-yourself, $29.50 including shipping (which only took three working days). Estimated job if down by appliance repairman, $140 (assuming the repairman didn't first erroneously blame the problem on faulty electronics then charge you hundreds of $$'s to replace circuits which were not broken to begin with, only to find the dishwasher still not washing/rinsing after his expensive electronic circuit replacements. The actually mechanical fix was cheap and simple. Truthfully, there is no excuse for Jenn Aire to ever use a plastic Chopper Sleeve in their dishwashers to begin with.......carefully planned obsolesence if you ask me. Oh well, it works perfect now. I doubt if even the four marbles my 4 year old had tried earlier to wash in my dishwasher (stripping out the original chopper sleeve) would do any damage to the metal replacement. However, I don't plan on testing my hunch. A simple fix, but a slightly challenging diagnosis which relied on a keen sense of hearing and a quiet workplace. Seems many people in these blogs have had the very same problem with their Jenn Air/Maytag dishwashers, and have made the same diagnosis and the same simple fix. Thank you mucho, PartSelect.