GJC3634RP02 Whirlpool Cooktop - Instructions

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.

Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

Its is very easy.Thakns for your tips.They take 30 minuts

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.

1. I ordered a replacement heater element from Parts Select, which arrived in just 3 days at my home. 2. I turned off the main circuit breaker to the range. 3. There are two small sheet metal screws inside the top left and right side of the oven door frame which need to be removed first in order to lift and remove the burner top from the range. 4. After lifting and pulling the burner top toward me about 6 inches, I unplugged the left and right burner assembly wiring harness connectors. 5. I lifted the burner top assembly off the stove and turned it upside down an a table. 6. There are six sheet metal screws that need to be removed to allow the sheet metal panel holding the heater assemblies to be lifted off and then also set upside down on a table top. All five burner elements are now visible. 7. Disconnect the slip-on electrical connectors to the specific heater assembly that is defective. 8. Unscrew the three small sheet metal screws from the three spring clips that support the heater assembly on the sheet metal panel; re-attach the spring clips to the new heater assembly. NOTE: Either memorize or record the position numbers that are cast into the ceramic housing of the burner to replace the new burner in exactly the same position. 9. Insert the three spring clips back into the sheet metal panel where the old, defective burner assembly had been removed. 10. Re-connect the slip-on wire clips to the new heater assembly in the same position as they were removed from the defective heater assembly. 11. Turn over the sheet metal panel with the burner assemblies attached and replace the sheet metal screws holding the panel to the stove top. 12. Turn over the stove top assembly and set back onto the range allowing space to reach to the back and re-connect the polarized connectors to the left and right side burners. 13. Slide the stove top back to the rear and carefully lower the front edge back down with the two metal tabs inserted back into the oven door frame. 14. Re-install the two sheet metal screws that hold down the stove top. 15. Turn on the main circuit breaker to the range. 16. Carefully test the new heater assembly by turning the range control knob to LO heat and watch for the stove top burner to momentarily turn red with heat. 17. Turn off the range control knob. 18. You are finished. It was a very easy installation.

Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.

first I checked continuity through the surface element (burner) switch (rheostat) which was fine. then found the screws holding the burner top on and removed, this made it possible to lift up the burner top and remove the burnt out surface element.which was easy to see. take down the number, buy a new one and re hook up the four wires to the new element. (always mark down where the wires went)

It's easier with two people.
1 - Turn the breaker for the range to OFF
2 - Verify power is off by testing the burners and lights
3 - Remove front two screws above oven door jamb
4 - Lift the top and prop it up with the spoon, or have your helper hold it.
5 - Loosen the screw at the rear of the bracket that holds the elements against the glass top (front and rear are held by the same retainer)
6 - Remove the bad element by sliding it sideways from the retainer. Do not disconnect things yet.
7 - The burner has numbers around the edge. Move brackets from old element to new one, matching the numbers. Then move wiring to new element. New burner may have a single connector where old one had 2 and a jumper. If so, ignore jumper.
8 - Slide new element under bracket and reinstall the screw.
9 - Lower the range top and re-install the screws.
10 - Turn on power and test.

Kill all power going to cook top.Remove knobs and lift cook top out of opening. Remove screws around outer edge of cook top, and lift glass top off of metal box.You must pry metal inward slightly to release glass top. Be carefull not to damage glass top. Now that top is removed take out two screws that hold switches in place and lift out piece that holds all switches and remove the two screws that hold the bad switch in place. Be careful and make a diagram of how the switch is wired. Remove wires on bad switch and wire to new switch. Wires are kind of short so you have to just pull switch to the side when you remove and replace wires. Make sure new switch is wired like old one. Put switch back in place. Put everything back together in reverse order of removal. Turn power back on and check operation.

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

First, I turned the circuit breaker off to the range. Then, I pulled the range out so that I could get to the screws which held the glass top in place. They were located on the sides of the range. I had to remove the trim pieces on the sides to get to the forward screws. Once that was done, I lifted the glass top, unplugged the wire harness, flpped it over on a protected surface. I noted the numbers on the old coil where the clips held it in place and put the clips on the new coil in the same place. The old wires just clipped on to the new coil exactly as they clipped on to the old coil. I put it all back together and it works great! I am a 70 year old woman who did this all by myself. You young guys should have no problem.